Search

Type: Posts; User: barrettb33

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    918

    You do not need a twin impeller setup. If you are...

    You do not need a twin impeller setup. If you are experiencing cavitation that bad then you need to check wear ring/impeller tolerance.
  2. Replies
    9
    Views
    747

    Your intercooler is leaking. The boost pressure...

    Your intercooler is leaking. The boost pressure blows into side a and then out of side b. That's why the foamy stuff is on that side. It's water in the intercooler core leaking and mixing with the...
  3. Replies
    38
    Views
    20,371

    There is no such thing as a 2002 Sportster with a...

    There is no such thing as a 2002 Sportster with a 215 SCIC engine.
  4. Replies
    38
    Views
    20,371

    You are not in the 70mph range with that boat...

    You are not in the 70mph range with that boat with just an X charger. The 2 bar intake grate cannot provide enough water to the pump to keep it hooked up to carry that kind of speed anyways. Once you...
  5. The venturi from a 2006 RXT is the exact same...

    The venturi from a 2006 RXT is the exact same size. It just has a bailout that you will have to plug with a 1/2" NPT PVC plug. Also it has a little tab for the RXT reverse gate spring, but it doesn't...
  6. Replies
    6
    Views
    657

    If you drill through the black on the hull, it's...

    If you drill through the black on the hull, it's actually 1/2" thick.
  7. Replies
    24
    Views
    1,727

    Have you checked your wear ring/impeller...

    Have you checked your wear ring/impeller tolerance? The max tolerance is .35mm.
  8. Replies
    11
    Views
    405

    FS Ok man I think I got it figured out. I still only...

    Ok man I think I got it figured out. I still only see the option to send you a visitor message. Try sending me a private message so that I can shoot you my phone number.
  9. Replies
    11
    Views
    405

    FS No one is trying to scam anyone. I just recently...

    No one is trying to scam anyone. I just recently joined this forum because I’m trying to gather more information for my 2006 Sportster build. Stop making assumptions. How am I going to scam him when...
  10. Replies
    11
    Views
    405

    FS View Post

    I looked through my settings and can’t figure out how to change that. Where in settings would I change that?
  11. FS I'll give you $250 shipped.

    I'll give you $250 shipped.
  12. Replies
    11
    Views
    405

    FS Shoot me a PM so we can arrange payment and...

    Shoot me a PM so we can arrange payment and shipping.
  13. Replies
    29
    Views
    2,943

    Yep! Torquing to 66in lb to do correctly you have...

    Yep! Torquing to 66in lb to do correctly you have to do it in 5-10 inlb increments and go around in a circle pattern on each bolt increasing the torque with each one. If not, you will end up just...
  14. The carbon seal material itself didn't change....

    The carbon seal material itself didn't change. Only the metal floating ring changed. They updated it to be more corrosion resistant. That's what was causing so many carbon seal failures was the metal...
  15. When it runs fine out of water, is the engine...

    When it runs fine out of water, is the engine compartment door open? If that's the case, then it sounds to me like you have a leaky exhaust system that is choking out the engine. This is because when...
  16. Replies
    1
    Views
    194

    I've used this in cars before and it actually...

    I've used this in cars before and it actually works. We've done it a few times for the track when we couldn't get race fuel. The same would work for an engine. However, if you are not tuned for the...
  17. Replies
    9
    Views
    2,049

    I can show you how I did it. I just trimmed about...

    I can show you how I did it. I just trimmed about 1/4 of the plastic off of the pump support where it meets with the rear plate on the intake grate. Then on the intake grate rear plate itself, on the...
  18. Replies
    9
    Views
    2,049

    I can show you how I did it. I just trimmed about...

    I can show you how I did it. I just trimmed about 1/4 of the plastic off of the pump support where it meets with the rear plate on the intake grate. Then on the intake grate rear plate itself, on the...
  19. Replies
    11
    Views
    405

    FS I'm interested. I sent you a PM.

    I'm interested. I sent you a PM.
  20. If you're only adjusting torque slip, no you...

    If you're only adjusting torque slip, no you don't need to balance it.
  21. IMHO just stick with plastic. If you ever were to...

    IMHO just stick with plastic. If you ever were to get corrosion build up between the stainless wear ring and the pump, it would cause the wear ring to create a bump that your impeller would wear on....
  22. Replies
    15
    Views
    1,060

    What color is the wear ring that you put in the...

    What color is the wear ring that you put in the pump? The OEM ones for the 159MM impeller are a light grey with black specks in it. Only use OEM wear rings if you're using plastic.
  23. Replies
    15
    Views
    1,060

    The original OEM 2 bar intake grate is no longer...

    The original OEM 2 bar intake grate is no longer available. You can put the intake grate from the 255 hp models on it though with a slight modification to the pump support. That intake grate is also...
  24. The bearing shouldn't have resistance. It looks...

    The bearing shouldn't have resistance. It looks like an aftermarket bellow/bearing. Use oem only!
  25. Replies
    1
    Views
    251

    Are you talking about the wear ring or the pump...

    Are you talking about the wear ring or the pump support where the pump bolts to?
Results 1 to 25 of 26
Page 1 of 2 1 2