Search

Type: Posts; User: urugol

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    14
    Views
    3,696

    If you have that much water in the case, and...

    If you have that much water in the case, and given the previous owner bought it like that I would say your crank bearings are well and truly gone. You will need to tear that engine right down, the...
  2. Replies
    4
    Views
    2,248

    You can't really do it easily without removing...

    You can't really do it easily without removing the exhaust. The main problem is getting to the cylinder base nuts on the exhaust side is very difficult, and for the extra bit of effort you will have...
  3. Replies
    76
    Views
    21,178

    I thought I would post an update on this as I...

    I thought I would post an update on this as I went out on an open water ocean ride about 5 miles off the coast this week, and I'm happy to report after dismantling and cleaning the injector...
  4. Replies
    12
    Views
    1,092

    I would go ahead and just swap that cylinder out....

    I would go ahead and just swap that cylinder out. Ideally you should consider getting the cylinder renik'd, millenium technologies are among the best in the business http://www.mt-llc.com/ Also...
  5. I don't think this case is what made Polaris stop...

    I don't think this case is what made Polaris stop producing pwc's, 10 million isn't a lot of cash for a big corporation and getting out of the industry alltogether does not exempt them from future...
  6. Replies
    16
    Views
    2,224

    Do not confuse the MSX140 with the MSX110/150,...

    Do not confuse the MSX140 with the MSX110/150, the 140 is the 2 stroke variant. The 110/150 were the first attempt at a four stroke by Polaris which had a ton of problems, followed by an exit of the...
  7. Replies
    16
    Views
    1,358

    =D>=D>Nice=D>=D> Pic 4 is my fav, would have...

    =D>=D>Nice=D>=D>

    Pic 4 is my fav, would have loved to see the landing though!
  8. Replies
    11
    Views
    1,070

    I have a feeling new jets will cost more than the...

    I have a feeling new jets will cost more than the new rack :p
  9. Replies
    33
    Views
    2,972

    Apply heat with a propane torch. That never...

    Apply heat with a propane torch. That never fails.
  10. Replies
    76
    Views
    21,178

    I'm not sure, I measured the outside diameter and...

    I'm not sure, I measured the outside diameter and width with digital callipers the numbers are accurate
  11. Replies
    76
    Views
    21,178

    I replaced the o-rings with much better used ones...

    I replaced the o-rings with much better used ones from another injector. It looks like they can be replaced with standard o-rings, with the exception of the top one which looks like a manufacturer...
  12. Replies
    76
    Views
    21,178

    Cleaned Injector

    So I got the confidence to go ahead and unscrew the injector to reveal the source of the rusty fluid. I'm glad I did, that bottom o-ring was clearly failing at the pressure these things run at its...
  13. Boat Catches Fire, Jetski Puts out Flames With Jet Pump

    This happened in Victoria, Australia last month in case anyone hasn't seen. V8 Inboard boat catches fire and there is no fire fighting equipment on board. The irony of being surrounded by...
  14. Replies
    76
    Views
    21,178

    =D>

    =D>
  15. Replies
    76
    Views
    21,178

    Thanks for the detailed response, yes I'm ok with...

    Thanks for the detailed response, yes I'm ok with the compensated vs non compensated issue I was putting it out there as I hadn't seen anyone here dismantle an injector before.

    They look like your...
  16. Replies
    76
    Views
    21,178

    Injectors are not programmable but there is data...

    Injectors are not programmable but there is data available to write them into your emm you just need to know where to get it.
  17. Replies
    76
    Views
    21,178

    Brad are you 100% on that information? I'm not...

    Brad are you 100% on that information? I'm not sending it to Dfi I will clean it up and change the orings first. It looks very straight forward to me. I gotta get off my butt and get me that...
  18. Replies
    76
    Views
    21,178

    So I took out the injector today to inspect. As...

    So I took out the injector today to inspect. As you can see from the pics, the injector is suffering from corrosion around the body which is reacting on the aluminium head. I sprayed it with some...
  19. Replies
    14
    Views
    997

    Looks like a stock 785 to me.....

    Looks like a stock 785 to me.....
  20. Thread: The ebay Bin

    by urugol
    Replies
    1,601
    Views
    196,256

    Sticky: I just picked this up...

    I just picked this up http://www.ebay.com/itm/370737197658?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649

    $40 for a brand new ficht injector with map disk! It's the 90 degree its worth seeing...
  21. Replies
    82
    Views
    7,149

    Can we bring our Sportsters?

    Can we bring our Sportsters?
  22. Replies
    18
    Views
    2,541

    Nice!! Actually it looks better than others I...

    Nice!! Actually it looks better than others I have seen I think the black in the middle makes it.
  23. Replies
    18
    Views
    2,541

    Pics beer man!

    Pics beer man!
  24. Replies
    18
    Views
    2,541

    Sending a seat from Australia would cost around...

    Sending a seat from Australia would cost around $400 return so it wouldn't be economical. I could get anything made here with a good upholsterer I suppose. I don't know why they need the seat,...
  25. Replies
    66
    Views
    4,329

    That's about 5% which is within service limits so...

    That's about 5% which is within service limits so that's ok. Comp is high I would be running premium gas on it. The thing that is confiusing is you mentioned it hit 6,000 rpm at one point, was that...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4