Search

Type: Posts; User: tiderider

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Just take i to the dealer, the cost of the tools...

    Just take i to the dealer, the cost of the tools won't make it worth your while. You may also cause further issues if its not put back together correctly.
  2. Replies
    2
    Views
    110

    Stock fuel pump is operated by the ECU, it...

    Stock fuel pump is operated by the ECU, it switches the fuel pump's ground (-), full load. The ECU also has to sense that the fuel pump fuse is drawing a current (+) as well. So if you fuse the fuel...
  3. Replies
    9
    Views
    297

    Sounds like you should have a mechanic point...

    Sounds like you should have a mechanic point things out and explain it to you in person..
  4. Replies
    9
    Views
    297

    You'll need to split the block, probably a good...

    You'll need to split the block, probably a good time to replace bearings if there is a lot of hours on the engine.. Remove connecting rod bolts, remove crankshaft and counter balance. The Pistons...
  5. Quench area issues?? Do install or not to install is the question??!!

    3 machinists have said, no problem with this cylinder head. A piston melted in #2 cylinder and there was some minor rough spots on the quench area of the cylinder head. It was cleaned by dremel,...
  6. SOLD Looking for a full set of titanium retainers

    Looking for a full set of titanium retainers for 4 tec. Let me know if you have some kicking around and gathering dirt?
  7. I check clearance with a bore gauge. Just to let...

    I check clearance with a bore gauge. Just to let you know that if your crankshaft journals are within specs, using WSM bearings work well for clearances at a fraction of the cost to OEM with the same...
  8. Crankshaft Pin maximum 45.048 1.7735 Crankshaft...

    Crankshaft Pin maximum 45.048 1.7735
    Crankshaft Pin Minimum 45.032 1.7729
    Crankshaft Pin Service limit 45.029 1.7728

    Crankshaft Pin Radial Clearances service limit 0.09 0.0035
  9. Replies
    1
    Views
    115

    If you have a candoo, you can test each injector...

    If you have a candoo, you can test each injector for function.. It can be wiring/connections or ECU.
  10. Replies
    6
    Views
    215

    Either a bad head gasket or oil cooler.. Any...

    Either a bad head gasket or oil cooler.. Any coolant mixing with the engine oil?
  11. Replies
    4
    Views
    323

    I can say that WSM bearings are good. I installed...

    I can say that WSM bearings are good. I installed a full set and clearances were perfect.
  12. Replies
    16
    Views
    567

    I'm pretty sure not all Siemens ECU can be...

    I'm pretty sure not all Siemens ECU can be tuned.. I have many logs to prove so..
  13. Replies
    16
    Views
    567

    I wouldn't waste your money trying to tune an...

    I wouldn't waste your money trying to tune an older Siemens ECU... No one can.. From my experience it was a 2007.
  14. Replies
    22
    Views
    566

    Tap on the retainers with the back handle of a...

    Tap on the retainers with the back handle of a hammer. You should hear the valve go in sligthly, it may take 2 tries sometimes. The single groove keepers make this much simpler.
  15. Replies
    29
    Views
    1,476

    That impeller bolt is part of the oil pump shaft,...

    That impeller bolt is part of the oil pump shaft, probably a good idea to replace as well.
  16. Replies
    22
    Views
    566

    Just tap on the valve stem's top a few times and...

    Just tap on the valve stem's top a few times and then try removing. Works every time.
  17. Replies
    22
    Views
    566

    Clean the threads on the crankshaft with a...

    Clean the threads on the crankshaft with a contact of some sort so the loctite sets fully when you install the flywheel bolts.
  18. The opening on the cylinder head for this nipple...

    The opening on the cylinder head for this nipple is 5mm. Hose is 1/4 inch.. Any guess to where they can be purchased as aftermarket?
  19. Thread: Engine Paint

    by tiderider
    Replies
    7
    Views
    358

    Its all about the prep work. I used Rustoleum...

    Its all about the prep work. I used Rustoleum high temperature with the mat black option. Holds strong now for years.
  20. Replies
    0
    Views
    75

    2007+ OEM 4tec valves issues?

    Any issues with the newer seadoo 4 tec valves from 2007+? Would they be okay to spin up 8600Rpms if stock sprigs are used with titanium retainers?
  21. FS - Parts Hi, Can you pm me about the Air intake manifold?...

    Hi, Can you pm me about the Air intake manifold? Thank you
  22. Replies
    4
    Views
    221

    SOLD Now those can't be good... Unless they are...

    Now those can't be good... Unless they are ARPs....
  23. Replies
    4
    Views
    221

    SOLD ARP Head studs

    Does anyone have a good clean set of ARP head studs kicking around for the seadoo 4 tec engines?
  24. Replies
    12
    Views
    489

    Yes the cylinder head can be removed without...

    Yes the cylinder head can be removed without pulling the engine.. It probably caused damage to the piston as well..
  25. Replies
    7
    Views
    361

    I did return a full set of Connection rod bolts...

    I did return a full set of Connection rod bolts back to SBT in the past.. 2 of the 6 bolts were cross threaded, they wouldn't screw in by hand.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4