Search

Type: Posts; User: HiPeRcO

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. You rang? :)

    You rang? :)
  2. Replies
    51
    Views
    1,036

    You need a VERY STOUT flywheel puller. Leave the...

    You need a VERY STOUT flywheel puller. Leave the nut on loosely, to keep the flywheel from doing it's SpaceX Falcon Heavy impression when it finally breaks loose.
  3. Unfortunately the effort to repair EMMs after he...

    Unfortunately the effort to repair EMMs after he has hacked and whacked upon them is even greater than ones that have not been repaired. So your best bet at this point is to make him stand behind...
  4. Replies
    3
    Views
    66

    Nope

    Nope
  5. Replies
    13
    Views
    221

    I've edited the post to add this important...

    I've edited the post to add this important information.
  6. Replies
    13
    Views
    221

    Everything on that list is Ethylene Glycol based...

    Everything on that list is Ethylene Glycol based :(
  7. In other words, he did his usual caliber of...

    In other words, he did his usual caliber of workmanship :facepalm:
  8. Thread: Msx 140 reeds

    by HiPeRcO
    Replies
    2
    Views
    81

    There are little or no things you can do to...

    There are little or no things you can do to increase the performance of a DI machine. It seems that you like to tinker, perhaps a carb machine would be better suited to your endeavors.
  9. Nice work, congrats!

    Nice work, congrats!
  10. Perhaps the EMM wasn't actually rebuilt, or it...

    Perhaps the EMM wasn't actually rebuilt, or it wasn't done properly. I (via Lakeside Tech) can test your EMM for you.
  11. Replies
    1
    Views
    253

    Candoo Pro is very good, and worth the money. ...

    Candoo Pro is very good, and worth the money. BUT most MSX150 issues can be sorted out without diagnostic software.
  12. Replies
    51
    Views
    1,036

    The Genesis flywheel can be R/R while in the...

    The Genesis flywheel can be R/R while in the hull. I've done it, and I'd probably do it again in the hull vs pulling the engine.
  13. Replies
    170
    Views
    5,426

    Measure continuity. Should be near zero ohms.

    Measure continuity. Should be near zero ohms.
  14. Replies
    13
    Views
    221

    DO NOT USE RV ANTIFREEZE, IT IS ALCOHOL BASED. ...

    DO NOT USE RV ANTIFREEZE, IT IS ALCOHOL BASED. USE PROPYLENE GLYCOL

    This is the OEM stuff. Comes concentrated, dilute about 50%

    Camco Ban Frost 2000 Marine - Engine Cooling Systems Only
  15. Replies
    170
    Views
    5,426

    Have you checked the wires from the coils to the...

    Have you checked the wires from the coils to the EMM for continuity?

    PIN 22 = OR/BLU = COIL 1
    PIN 2 = OR/GRN = COIL 2


    Have you removed the coils and cleaned the grounding tabs? Have you...
  16. Welcome to Greenhulk! A few comments: - The...

    Welcome to Greenhulk!

    A few comments:

    - The need to prime to get the engine started is a classic symptom of low injector volts while cranking. Either due to a bad flywheel/stator, or a bad...
  17. Sticky: I have never had any luck scanning barcodes with...

    I have never had any luck scanning barcodes with an Android device, but a customer recently shared with me that this app works :)

    (QR & Barcode Reader from TeaCapps)

    ...
  18. Try swapping the SIFB from the running machine.

    Try swapping the SIFB from the running machine.
  19. Replies
    9
    Views
    253

    Welcome to Greenhulk! @Ye Ol Salty Dog is the...

    Welcome to Greenhulk!

    @Ye Ol Salty Dog is the MSX whisperer and is in the Tampa region. I've turned on the MSX beacon to summon him here :)
  20. Replies
    8
    Views
    198

    Totally unscientific observation, but I think the...

    Totally unscientific observation, but I think the older spade terminal style LR503 modules are more reliable...
  21. Replies
    14
    Views
    595

    Lakeside Tech will be glad to help.

    Lakeside Tech will be glad to help.
  22. Replies
    73
    Views
    47,379

    Sticky: I fixed the link, try it again.

    I fixed the link, try it again.
  23. WTB Get a hold of Joe at Cliffside Power Machines...

    Get a hold of Joe at Cliffside Power Machines
  24. Replies
    13
    Views
    412

    That is perfectly normal appearance. The...

    That is perfectly normal appearance. The microprocessor has dielectric grease applied to the pins.

    Most of the ways the EMMs fail do not illuminate the check engine light.

    A better place to do...
  25. Replies
    13
    Views
    412

    I'd also add 8. NGK PZFR7G-G spark plugs. No...

    I'd also add

    8. NGK PZFR7G-G spark plugs. No substitutes!

    Lakeside Tech will be happy to repair the EMM, if it comes to that.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4