Search

Type: Posts; User: HDAV

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    470

    @djsil is having similar issue I think

    @djsil is having similar issue I think
  2. Replies
    8
    Views
    470

    Hmmmmm gear on end of SC shaft all good?

    Hmmmmm gear on end of SC shaft all good?
  3. Replies
    8
    Views
    470

    SC was primed with oil when re-installed? No give...

    SC was primed with oil when re-installed? No give back wards on the wheel? Upgraded gear set as well as clutch?

    BOV leaking?
  4. The old 2 stroke wave venture had that style of...

    The old 2 stroke wave venture had that style of pump not used on modern 4 stroke skis but there are companies that make them for adapting for jet boats
    ...
  5. Replies
    6
    Views
    177

    Seems quite a bit check the rings............my...

    Seems quite a bit check the rings............my 1800 uses no oil between changes.......

    know stuck rings are an issue on the vx1100 motors lots of WOT will use more oil

    you are checking it...
  6. Replies
    13
    Views
    560

    If chain is centred on the gears, later design is...

    If chain is centred on the gears, later design is 5 links wide not 3 like the original, (may need wider guides) why would it move? That’s surely only as likely as the thinner chain falling off the...
  7. Replies
    10
    Views
    495

    New longer wider hull.........

    New longer wider hull.........
  8. hopefully not but compression test is the answer,...

    hopefully not but compression test is the answer, make sure the oil level is correct. I would be more concerned about corrosion in side the motor with such low hours..... average of 4 per year is a...
  9. Replies
    2
    Views
    103

    Hmmm oil on the anode that’s a new one......

    Hmmm oil on the anode that’s a new one......
  10. Replies
    9
    Views
    491

    I use the middle one..... easy to keep in ski and...

    I use the middle one..... easy to keep in ski and mostly plastic so won’t rust too fast.....

    https://www.harborfreight.com/Line-Clamp-Set-3-Pc-63596.html
  11. Replies
    4
    Views
    164

    Compression test..........

    Compression test..........
  12. Replies
    9
    Views
    491

    Clamp off the cooling water line from pump to X...

    Clamp off the cooling water line from pump to X where flush port connects.... make sure revere bucket is raised! As no water can get into the cooling system you can tow as fast as you wish.....

    ...
  13. Replies
    6
    Views
    294

    Jeeeezzzz you guys care more about the look of...

    Jeeeezzzz you guys care more about the look of the engine bay than how they ride...... yeah knock a bit off for it being crusty.... don’t buy waverunner to save money... ride em hard enjoy them sell...
  14. Replies
    6
    Views
    294

    2016 is a solid year, hours are low were they...

    2016 is a solid year, hours are low were they serviced each year as per manual? Used in salt water or fresh? Any outward signs of corrosion damage? Any corrosion tot he ride plate or pump? Do they...
  15. Thread: Water in intake

    by HDAV
    Replies
    3
    Views
    102

    So someone opened the plugs while it was sitting?

    So someone opened the plugs while it was sitting?
  16. Thread: Water in intake

    by HDAV
    Replies
    3
    Views
    102

    Do you know why it sank? Shop vac as much water...

    Do you know why it sank? Shop vac as much water out as you, can is oil clean?

    You may need to pull the J pipe off and dry it and intercooler if you have an intercooler full of water.........
    ...
  17. Replies
    12
    Views
    296

    Yeah but never seen a white hull turned black...

    Yeah but never seen a white hull turned black during a ride! That’s not normal surely.......

    i should have taken a picture picture but the whole rear of ski was black
  18. Replies
    12
    Views
    296

    Then why the soot? The oil is yamalube 2T I...

    Then why the soot? The oil is yamalube 2T I think....how do you adjust the pump?
  19. Replies
    12
    Views
    296

    That is fine if a you want to run premix and b...

    That is fine if a you want to run premix and b the issue is the pump over oiling.......
  20. Replies
    4
    Views
    244

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=454118&stc=1Google the service manual its out there for a 2008 sho same motor...my advice change the sensor.....
  21. Replacing rear gunwhale trims removing old rivets

    So I need to replace the rear gunwhale trims on my fx......do I just drill them out or do I need to do something else? Also is a special tool
    needed to fit them or will a basic hand riveter work?
  22. Thread: Water in hull

    by HDAV
    Replies
    9
    Views
    491

    Thanks only wish I had a local hardware store...

    Thanks only wish I had a local hardware store that carried that kind of stuff.....
  23. Replies
    14
    Views
    866

    Fingers crossed you find a good motor...

    Fingers crossed you find a good motor...
  24. different style but I keep one of these rolled...

    different style but I keep one of these rolled up for exactly these occasions takes seconds to throw on and saves the leather getting wet and salty.....
    ...
  25. Replies
    12
    Views
    296

    Still oil injected yes and max oil flow would...

    Still oil injected yes and max oil flow would explain why it runs fine at WOt but won’t idle and is really sooty (not normal) and happens after a recent ride

    Is it the cable 66E-26320-00-00 PUMP...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4