Search

Page 1 of 2 1 2

Search: Search took 1.00 seconds.

  1. Replies
    16
    Views
    1,090

    Thanks, man! It's been a pretty fun build, even...

    Thanks, man! It's been a pretty fun build, even with my OCD kicking in lol. I wish I knew even 10% of all the little tricks the guys did back in the day for that slight edge over those XPs.
  2. Replies
    16
    Views
    1,090

    Oh hell yeah! It sounds crazy in person hearing...

    Oh hell yeah! It sounds crazy in person hearing it humming at those RPMs.

    I've seen a few MSD installations where the components were bolted directly onto the side of the hull and I didn't like...
  3. Replies
    5
    Views
    462

    You've basically found the two remaining piston...

    You've basically found the two remaining piston sources for our 785s...Wiseco or WSM. You'll probably never find another stock 785 piston unless someone has one laying around in their garage. I'd...
  4. Replies
    74
    Views
    10,926

    Long time since an update....are those Dave...

    Long time since an update....are those Dave DeLaughter ported cylinders????
  5. Replies
    13
    Views
    1,759

    Wow, poor thing!!! I'm sure others will agree...

    Wow, poor thing!!! I'm sure others will agree but you need to completely tear that thing apart and go over EVERY...SINGLE...THING. You can't trust anything was done correctly with that sort of...
  6. Off chance your wedge is upside down?

    Off chance your wedge is upside down?
  7. I would take carb cleaner and use the straw to...

    I would take carb cleaner and use the straw to blow out each fitting, including the other two. They may be gunked up closed and the center carb is gunked up open.
  8. The stub shaft is backwards. You have the treads...

    The stub shaft is backwards. You have the treads going out the back of the stator when it should be coming out the other side. There should also be a black plastic cone that bolts to the back of...
  9. I made a thread about how to disassemble, clean...

    I made a thread about how to disassemble, clean and reassemble your bendix. There are also plenty on eBay but it is pretty easy to clean...

    http://www.greenhulk.net/forums/showthread.php?t=268628
  10. Replies
    3
    Views
    878

    I'd reconsider the use of an electric fuel pump;...

    I'd reconsider the use of an electric fuel pump; you obviously have another issue that is causing the fuel starvation and the electric pump is nothing more than a band-aid for another underlying...
  11. Replies
    209
    Views
    20,640

    I had my first race of the season this last...

    I had my first race of the season this last weekend and I had an absolute blast! The Red Top carbs were a definite upgrade over the stock carbs. The 125 pilot / 125 main with 2.3 N/S and 95 gram...
  12. Replies
    74
    Views
    10,926

    A bit of an update to this project. I have not...

    A bit of an update to this project. I have not been able to do too much over the last month or so due to the crappy weather we've been having here in Texas...be it ice or downpours. The sanding of...
  13. Replies
    7
    Views
    1,560

    The gear that drives the flywheel has two concave...

    The gear that drives the flywheel has two concave washers that create the tension to hold the middle section together. I used two c-clamps to remove the next snap ring.

    If your bendix is...
  14. Replies
    74
    Views
    10,926

    After working all day, I have the hull stripped...

    After working all day, I have the hull stripped completely and all of the old bonding goop removed. I am 100% sure this has to be a light weight hull...I can lift it easily with one hand.

    Plan of...
  15. Replies
    12
    Views
    839

    Something like this?

    Something like this?
  16. Unless you're running high compression or some...

    Unless you're running high compression or some crazy ignition curves, you don't need race gas and might find that it won't run as well with the high octane. Remember that octane is resistance to...
  17. Replies
    78
    Views
    4,486

    froeman, I just saw you posted his earlier...

    froeman, I just saw you posted his earlier today...



    You really need to keep your issues to a single thread instead of posting replies everywhere. It is hard to determine what may be your...
  18. Replies
    78
    Views
    4,486

    Probably okay then. Does it run better with the...

    Probably okay then. Does it run better with the choke closed up?
  19. Replies
    78
    Views
    4,486

    What do you mean it releases air? It should allow...

    What do you mean it releases air? It should allow air to go in but not back out....so as your ski burns fuel, it will let air into the tank due to the removed fuel volume and the other allows the...
  20. Replies
    78
    Views
    4,486

    Check your fuel tank relief valves...there will...

    Check your fuel tank relief valves...there will be two, one to hold pressure at about 2 psi and the other to let air into the tank.
  21. Replies
    74
    Views
    10,926

    Here is a video of the first ride out on the...

    Here is a video of the first ride out on the water..

    https://www.youtube.com/watch?v=dMNTZiqI65k
  22. Replies
    74
    Views
    10,926

    Haha funny! Almost done with this boat. I...

    Haha funny!

    Almost done with this boat. I wanted to take it out last weekend but work hampered that throughout the week...couldn't quite get it finished.

    The engine took a serious 180 as far...
  23. Replies
    74
    Views
    10,926

    Water system is all done. Electrical system is...

    Water system is all done. Electrical system is all done.

    I rebuilt the carbs last night but I need to check the pop off before I completely assemble and do the fuel system. This boat didnt even...
  24. Replies
    74
    Views
    10,926

    Okay, pipes are installed. The electrical is all...

    Okay, pipes are installed. The electrical is all hooked up....there is good spark on all 3 plugs.

    Checked the compression and I'm at 155 MAG, 150 CEN, 150 PTO. Not too bad!

    Now to finish...
  25. Replies
    74
    Views
    10,926

    Got a little more done today. I honestly wanted...

    Got a little more done today. I honestly wanted to have it running by this weekend but I decided that I didn't want to rush it. These pipes have been giving me hell getting into the ski. I had no...
Results 1 to 25 of 44
Page 1 of 2 1 2