Search

Type: Posts; User: EVN81

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    22
    Views
    738

    Where you found a new brass fitting? I found...

    Where you found a new brass fitting?

    I found the threaded piece back in the hull, came out due vibration I guess...

    450470
  2. Siphon tubes will not keep up if the carbon seal...

    Siphon tubes will not keep up if the carbon seal fails.
    Water comes in quick and backside of ski goes down pretty quick.
    For me thatís the main reason to have a pump installed at the back of the...
  3. Replies
    5
    Views
    107

    If it occurs and eventually it tops out 72 let go...

    If it occurs and eventually it tops out 72 let go the throttle and go back to idle.
    Then pin it again, thereís not yet condensation build up.
    So if it re-occures it could be the map.
    If not you...
  4. Replies
    14
    Views
    497

    The crank need some axial play after install of...

    The crank need some axial play after install of thrust washer due heat expansion.
    Probably somewhere material was left behind at the case or at the crank.

    Try new thrust washer again and remove...
  5. Replies
    70
    Views
    7,204

    Thanks for sharing this info [emoji106] Do you...

    Thanks for sharing this info [emoji106]

    Do you maybe know whatís the difference between kit 198 (RXT) & 199 (RXP) for 300 models?

    Is it the carbon material (probably not) or the dimensions of...
  6. Replies
    3
    Views
    389

    SOLD Up

    Up
  7. If you use the black 3/4 outlets from GH store...

    If you use the black 3/4 outlets from GH store you can just push the garden hose in there.

    Clamp of the small 3/8 hose from exhaust manifold to waterbox and you can do it with engine stopped.
  8. Replies
    70
    Views
    7,204

    That makes sense. The pictures of Fishpro are...

    That makes sense. The pictures of Fishpro are crazy.
    Never seen it so bad, even with broken engine mounts!
  9. Replies
    70
    Views
    7,204

    Workshop manual is usefull as well ...

    Workshop manual is usefull as well

    https://brpmanuals.com/seadoo-manual.htm

    Scroll all the way down for your model 2019
  10. Replies
    797
    Views
    95,755

    VIN is located rightside aft or on your...

    VIN is located rightside aft or on your documentation.

    Last 2 digits is the model year (yours 18 )
    3rd last is the year of production (should be 7 or 8 )
    4th last is a letter which is the month...
  11. Replies
    797
    Views
    95,755

    Man that sucks if your new ski looks like that!...

    Man that sucks if your new ski looks like that!
    What are the last 4 letter/numbers of the VIN?
    Just wondering if itís an early production.

    FWIW I use this without any problem on the CM-tec

    ...
  12. Replies
    14
    Views
    677

    My manual says the same but this must be the hard...

    My manual says the same but this must be the hard limiter.

    ECU will always regulate back to 8040.
    And thereís also the speed and torque limiters.

    I ran several different props with stock ECU...
  13. Replies
    14
    Views
    677

    View Post

    Donít be suprised if water comes out. In hotter climates there can be a lot of condensation.
    A pressure test is good way to verify.
    If riding salt itís easier to sea as itís everywhere.....
    ...
  14. It worked for me

    It worked for me
  15. Replies
    14
    Views
    677

    RPMs slightly down. What gives?

    Drop of rpmís and no alarms or faultcodes on a 2013 ski?

    Check your IC!

    When water leaks in the charge air it slows down your engine.
    Very very common issue on the earlier 260 models.

    All...
  16. View Post

    Yes thereís a thread about that.
    I think it was the one you pull the temp. graph from.

    If youíre able to monitor AIT you can see the effect of every change you do.

    If you install a strainer...
  17. View Post

    You can go with 3/4Ē outlet.
    The first T-piece should have an internal restriction towards inlet hose IC.
    Towards exhaust manifold is full bore.

    Pull hose to check because Ď16 / Ď17 models are...
  18. Replies
    7
    Views
    371

    DashFlash also offers the speed limiter removal

    DashFlash also offers the speed limiter removal
  19. Replies
    70
    Views
    7,204

    Not that easy, the culprit is you need the...

    Not that easy, the culprit is you need the alignment tools to do the job properly.

    Not just install all new (basically all IS new with all these low hours)
  20. Replies
    70
    Views
    7,204

    View Post

    0 Hours [emoji23]
    Iím not sure whatís off, engine or tru-hull....
    Also rubber flap is to short and not completely covering carbon ring.....
    449483
  21. Replies
    4
    Views
    365

    View Post

    Ah ok my bad, that I donít know!
  22. Replies
    20
    Views
    10,079

    +1 [emoji3]

    +1 [emoji3]
  23. Replies
    4
    Views
    365

    Yes it will fit. It gives more tension on the...

    Yes it will fit. It gives more tension on the bellow.

    You might have some installation issue due the hat touching the SC during the re- installation of SC.
    I assume you take SC out to have more...
  24. https://brpmanuals.com/seadoo-manual.htm ...

    https://brpmanuals.com/seadoo-manual.htm

    Scroll down for 2008
    $ 9.50
    You get the manual as PDF file without any restrictions!
  25. Thread: IBR fault code

    by EVN81
    Replies
    11
    Views
    540

    Serious does anybody read the owners...

    Serious does anybody read the owners manual.........?

    Page 111 (for RXP)
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4