Search

Type: Posts; User: Myself

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    4
    Views
    99

    When I replaced the thermostat it looked dandy....

    When I replaced the thermostat it looked dandy. Machine has 109 freshwater hours on it. Wondering if I have some air trapped in the ride plate. What is normal temp drop through the plate?
  2. Replies
    4
    Views
    99

    Already went through exhaust cooling side, all...

    Already went through exhaust cooling side, all good. I've got a warmer than normal engine side it appears. Hooked up Candoo this evening....last 60 seconds runtime shows 190-196*. Min max history...
  3. Replies
    4
    Views
    99

    Help me out guys '05 RXT H-temp alarm

    History....customer buys pair of Seadoos that had been sitting unused for 3 years. First time out te RXT overheats and he has to add coolant like every 5 minutes!! Brings it to me.

    I drain...
  4. Replies
    7
    Views
    105

    If you feel like it needs more than the factory...

    If you feel like it needs more than the factory rubber lip seal then smear a bit of case sealant around them. 3 Bond, Yamabond, Motoseal, etc.
  5. Replies
    8
    Views
    139

    Yes, the newer it is, the bigger it is, and more...

    Yes, the newer it is, the bigger it is, and more powerful too. The old 440/550 Kawi's are very narrow and short = harder to ride. Then came the 650 Kawi and Yamaha Superjet....MUCH more stable and...
  6. Replies
    8
    Views
    139

    Yes, it IS great exercise. It is like riding a...

    Yes, it IS great exercise. It is like riding a bike in many ways.......including PRACTICE! It's really a combination of steering, leaning, and throttle. GO FASTER!!! It's actually hard to go slow...
  7. Replies
    1
    Views
    63

    2-Stroke Nice project, I just fixed and sold a '98 XL1200.

    Nice project, I just fixed and sold a '98 XL1200.
  8. Replies
    2
    Views
    101

    Sounds like there is still some debris in the...

    Sounds like there is still some debris in the pump somewhere.
  9. Replies
    6
    Views
    157

    I literall just finished assembly of a 750...

    I literall just finished assembly of a 750 rebuild this morning! Going back into the ski this afternoon.
  10. Sounds like you're referring to the backlash of...

    Sounds like you're referring to the backlash of the driven gear against the flywheel gear. Perfectly normal.
  11. If, in fact, they left the flywheel from the 2...

    If, in fact, they left the flywheel from the 2 coil version with the single coil MPEM..............YEP, not gonna work.
  12. Replies
    1
    Views
    80

    Random dying a lot of times is the DESS post. ...

    Random dying a lot of times is the DESS post. Bogging is normally carb rlated. Strictly based on age you need to rebuild the carbs.
  13. Replies
    5
    Views
    123

    Boats came with different fuel line to comply...

    Boats came with different fuel line to comply with USCG regulations. Have you checked out the jet pumps? What's the condition of the wear rings?
  14. Replies
    3
    Views
    110

    either will be fine. I like WSMs bearings better.

    either will be fine. I like WSMs bearings better.
  15. Replies
    5
    Views
    127

    yes, when the pump bearings fall apart, the...

    yes, when the pump bearings fall apart, the impeller thrusts forward pushing into the engine.
  16. Replies
    5
    Views
    140

    Those are bad about one of the cooling lines...

    Those are bad about one of the cooling lines popping off at the rear. Just take out the 10mm bolts holding the rear seat support onto the hull and look back where they hook to the pump.
  17. You're getting 12v low message, pulsing cranking,...

    You're getting 12v low message, pulsing cranking, and cranks over fine with stator unplugged.......sounds like the voltage regulator has crapped.......which is INSIDE the MPEM. There is a kit from...
  18. Replies
    8
    Views
    202

    Wait, you already have a 1300. Get an FZR.

    Wait, you already have a 1300. Get an FZR.
  19. Replies
    19
    Views
    404

    I've never been a fan of primers. I always remove...

    I've never been a fan of primers. I always remove the acc pump, do the balanced return mod, and set up jetting and screws to Euro specs. They starteasy and run great every time.
  20. 07-09 Most models no start, no display, completely dead

    Another member and I both had skis doing this exact thing and it's pretty tough to troubleshoot without a wiring schematic and a pretty good grasp on electrical systems. Thought this might help...
  21. Replies
    4
    Views
    5,158

    Same on all the Seadoo 2 strokes.

    Same on all the Seadoo 2 strokes.
  22. I've done hundreds of rebuilds....mostly 2...

    I've done hundreds of rebuilds....mostly 2 stroke, but also several 4 strokes. A complete disassembly, inspection, parts cleaning, bilge cleaning, and reassembly on a 4 stroke is in the 40hr range. ...
  23. Well......that's what I thought was going on....

    Well......that's what I thought was going on. Man, I wish I could have got my post installed before you had to give up that much cash. You would have only been out the part money.



    Also fixed...
  24. Replies
    9
    Views
    364

    It seems to me that if you have the first gen...

    It seems to me that if you have the first gen domestic twin ignition, it's usually the stator giving "no spark". But on the '99 up domestic twin, it seems to usually be the cdi. Just something I've...
  25. Replies
    12
    Views
    276

    I know on the Tigershark 1100, the Ficht Di has a...

    I know on the Tigershark 1100, the Ficht Di has a different taper on the crank snout for the different magneto.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4