Search

Type: Posts; User: turboman412

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    5
    Views
    139

    WTB - Parts I have a good water pipe and many balance gears

    I have a good water pipe and many balance gears
  2. Do you have the factory pipe install video?...

    Do you have the factory pipe install video? Pretty sure they retain the stock oil injection
  3. Replies
    2
    Views
    120

    Correct, from my memory the collar goes on...

    Correct, from my memory the collar goes on inside. Do you will have to remove the 3 seals or the big bearing
  4. Yes, shred master is an improvement over the...

    Yes, shred master is an improvement over the stock and r&d. Gets the front of the hull out of the water more and makes ski feel lighter. Very very happy with it and thankful i was able to find one a...
  5. Yes they make a huge difference, ski also has a...

    Yes they make a huge difference, ski also has a umi set up, worx intake and a shredmaster ride plate449466
  6. I finally got mine dug out and ready to use this...

    I finally got mine dug out and ready to use this fathers day with my wife! Cant wait449452
  7. Only way is with engine bolted try to lift with a...

    Only way is with engine bolted try to lift with a prybar. Kinda like a timing belt, everything thing seems fine till it lets go. Front motor mount breaking is very common on these 1200s not so much...
  8. Replies
    5
    Views
    139

    WTB - Parts I also have one

    I also have one
  9. Thats your choice I have run the wsm mounts...

    Thats your choice

    I have run the wsm mounts with good success, rhaas makes the best mounts for these i have seen
  10. Theres problems with the front mount pulling out...

    Theres problems with the front mount pulling out on both stxr and ultra. Make sure a good mount or the ski can sink. Rhass makes a good set up
  11. Replies
    5
    Views
    169

    Should be supported at front of engine at one of...

    Should be supported at front of engine at one of the studs for water manifold. Thats my guess why it broke
  12. Replies
    5
    Views
    169

    Is the cable supported on the water manifold?

    Is the cable supported on the water manifold?
  13. A ball hone will do nothing to a plated cylinder...

    A ball hone will do nothing to a plated cylinder unless its a diamond hone.

    Pwc engines used wsm parts, i have had him do a few cranks for me and they come out awesome.

    Us chrome for replate,...
  14. All gaskets other then the arrester gaskets are...

    All gaskets other then the arrester gaskets are one time use...

    Just keep in mind those remains could use sleeve cylinders, sbt deff uses sleeved with junk parts
  15. No, like mentioned before this could have...

    No, like mentioned before this could have happened before you purchased it. Most likely its an issue with the carb or a clogged pisser tube or even a lose spark plug.

    I have had them pop on me...
  16. Go with pwc engines if your go rebuilt, just the...

    Go with pwc engines if your go rebuilt, just the sound of sbt makes me cringe
  17. Cylinders are plated, you need a diamond hone to...

    Cylinders are plated, you need a diamond hone to clean that up. Not many machine shops can do this, a used cylinder might be in order.
  18. Replies
    3
    Views
    123

    Looks good

    Looks good
  19. Coupler is where the drive shaft connects. I...

    Coupler is where the drive shaft connects.

    I will always recommend rebuilding yourself, but keep in mind these 1200s get pricey
  20. Grab the coupler and spin with your hand, is the...

    Grab the coupler and spin with your hand, is the bottom end locked up now? Feel the bottom make sure there is no hole in the case now. Normally when a skirt breaks the crank punches it through the...
  21. Detonation caused the hole, looks like some light...

    Detonation caused the hole, looks like some light seizing on other cylinders. Engine has to come out, cyliners pulled and case split to inspect crank..

    What fuel did you run? Like i said many...
  22. Replies
    3
    Views
    123

    Wsm or oem

    Wsm or oem
  23. Guys are right not spinning over 4500 rpm sounds...

    Guys are right not spinning over 4500 rpm sounds like a dead cylinder. Easiest thing to do is pull the head and have a look
  24. Look in manual for part number of tool, i...

    Look in manual for part number of tool, i purchased mine off ebay...
  25. I mean the tool your supposed to lock in the vice...

    I mean the tool your supposed to lock in the vice and pump drops into?449098
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4