Search

Type: Posts; User: Robb235

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    11
    Views
    360

    Spent some time this weekend building my fuel...

    Spent some time this weekend building my fuel pump assembly to accommodate the MR1ís fuel injection system.

    I slid the fuel pump down a little bit further after I snapped the pictures.

    I have...
  2. Replies
    11
    Views
    360

    XR1800 160hp MR1 Conversion

    So I went browsing on the tach manufactureís (Beede) website, and found what appears to be the pin out for the exact Yamaha tachs I have, pictured in my previous post. From what I can tell, itís a...
  3. Replies
    54
    Views
    8,961

    Poll: 2-Stroke View Post

    Thanks for the information.

    Iím using several of the ideas discussed in this thread for my own XR1800 engine swap. Iím using a pair of MR1 HO motors instead of the 1.8s.

    Link to my thread...
  4. Replies
    11
    Views
    360

    XR1800 160hp MR1 Conversion

    So I picked up a pair of a pair of SX230/AR230 HO tachometers. In addition to hooking up the tach signal, ideally Iíd like to also hook up the three warning lights: Check Engine, Low Oil, and...
  5. Replies
    11
    Views
    360

    Next step is to prime and paint the rails, since...

    Next step is to prime and paint the rails, since the rails are steel. I think Iím going to try this stuff.

    464333
  6. Replies
    11
    Views
    360

    XR1800 160hp MR1 Conversion

    Did some more test fitting this weekend using my 3/16Ē flat steel rails. That seems to be the perfect thickness for the rails; I was able to align the motor without any shims.

    464329

    464330
    ...
  7. Replies
    2
    Views
    484

    How much boost?

    How much boost?
  8. Replies
    11
    Views
    360

    XR1800 160hp MR1 Conversion

    So I went into this project not realizing I would have to cut up the engine bay a little bit to make these MR1 motors fit. When reading the other guyís thread on YJB, I knew the motor mounts would...
  9. Replies
    11
    Views
    360

    XR1800 160hp MR1 Conversion

    I rolled my engine dolly outside and cranked up Engine #1. What a beautiful sound compared to the 2-strokes.

    I have the fuel pump removed from the pump assembly and submerged in the red gas can. ...
  10. Replies
    11
    Views
    360

    XR1800 160hp MR1 Conversion

    I bypassed the Yamaha remote system by splicing together yellow to yellow, blue/black to black/blue, and blue to black. After those connections are made, need to run switched power to the yellow...
  11. Replies
    11
    Views
    360

    XR1800 160hp MR1 Conversion

    I pulled the motors out of the skis, and realized I was going to need a new, beefier work bench. The bench I had before was left over from the previous home owners, and was much too small. I also...
  12. Replies
    11
    Views
    360

    XR1800 160hp MR1 Conversion

    I sold both of my 1200 power valve motors and a carb rack to fund the purchase of an Ď05 FXHO and an Ď05 FX Cruiser. I found these gems in Texas while on a jobsite visit for work. The skis had about...
  13. Replies
    11
    Views
    360

    XR1800 160hp MR1 Conversion

    I think Iím far enough along on my 4-stroke swap that I can start sharing my progress.

    Iíve owned my XR1800 for about 5 years, and while I like the boat, Iím just not a fan of either the...
  14. Replies
    1
    Views
    150

    Echo Echo Echo Echo .

    Echo

    Echo

    Echo

    Echo

    .
  15. Replies
    1
    Views
    150

    Disassembling MR1 Fuel Pump Assembly?

    I did a search, but didnít find what I was looking for.

    Is there a guide on taking apart the fuel pump assembly so that I can replace the pump itself? Not real sure how to take this thing apart....
  16. SOLD All are SOLD.

    All are SOLD.
  17. Replies
    54
    Views
    8,961

    Poll: 2-Stroke How do both engines/ECUs control the single fuel...

    How do both engines/ECUs control the single fuel pump?
  18. Replies
    5
    Views
    278

    View Post

    Iím not familiar with that tool. How does it hold the crank still?
  19. Replies
    5
    Views
    278

    View Post

    Yeah, Iím not sure if the valves are open or not. Thatís exactly what Iím afraid of.
  20. Replies
    5
    Views
    278

    How To Remove '05 FXHO MR-1 Drive Coupler

    How are you guys removing the drive coupler with the crank still in the engine? Engine is completely together sitting on my work bench, and I need to get the drive coupler off so that I can put on...
  21. Replies
    0
    Views
    136

    What is MR1 weight?

    Iíve got two MR1 motors, the 160hp variants, one of which is sitting on my new wood workbench I just built. Need to know the approximate weight of the motor, I put casters on the bottom of the legs...
  22. Replies
    9
    Views
    569

    FS - Parts 66V T-Handle Adjustment Screws "EZ Tune"

    My assumption would be yes, but I honestly have no idea.
  23. Replies
    9
    Views
    569

    FS - Parts Still have the last set for sale. Will do one...

    Still have the last set for sale. Will do one complete motor (3 carbs).
  24. Replies
    4
    Views
    584

    View Post

    Lol you canít say ďClass dismissedĒ right after you just said ďMy guess is...Ē

    [emoji1787][emoji23][emoji1787][emoji23]
  25. Replies
    4
    Views
    584

    FXHO Pump Differences

    I need a quick education on early 2000ís jet pumps. What is the difference between, say the Ď05 FXHO jet pump, and the older style ďnon-HOĒ jet pumps. Theyíre both 155mm, right?
Results 1 to 25 of 165
Page 1 of 7 1 2 3 4