Search

Type: Posts; User: savageman69

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. it takes no special tools at all to at least...

    it takes no special tools at all to at least check static timing...ive done lots of ignition updates and never needed to adjust timing personally
  2. Replies
    4
    Views
    102

    yes its an issue...thrust will be significantly...

    yes its an issue...thrust will be significantly reduced
  3. Replies
    9
    Views
    429

    look pretty lean too, no one has oem kits right...

    look pretty lean too, no one has oem kits right now even watcon due to supply shortage
  4. ive been told by multiple guys i consider...

    ive been told by multiple guys i consider pros...the real nujet 7 is the best
  5. Replies
    8
    Views
    2,144

    regardless the 1050s need bigger mids...all mine...

    regardless the 1050s need bigger mids...all mine were way lean and worked better with bigger mids...most 1050s suffer from falling on the face in the mids due to lack of fueling....casey is the man...
  6. no water should enter the hull at all while not...

    no water should enter the hull at all while not moving. You have a loose clamp or blown hose. The bilge pump is designed to be submerged its fine
  7. wsm is not oem kits...oem or its junk it will...

    wsm is not oem kits...oem or its junk it will likely eat a piston with them in
  8. Replies
    4
    Views
    167

    Thats not a thing

    Thats not a thing
  9. what have you done to the carbs? white plug is...

    what have you done to the carbs? white plug is lean...and not likely a high jet issue either dirty or blocked carb or cheap rebuild kits...are the fuel lines grey.

    ive never had a thermostat or...
  10. those pistons look pretty close to lean

    those pistons look pretty close to lean
  11. thats lean..just fixed a genesis like this pulse...

    thats lean..just fixed a genesis like this pulse line was off on pto carb pump.....another thing aftermarket kits are junk
  12. Replies
    12
    Views
    1,053

    will look better cleaned and finished and in the...

    will look better cleaned and finished and in the sun so the metallic comes out
  13. Replies
    12
    Views
    1,053

    working away https://i.imgur.com/x2jgMnTh.jpg...

    working away

    https://i.imgur.com/x2jgMnTh.jpg


    https://i.imgur.com/JJZ4QlHh.jpg
  14. you can still buy unsealed batteries? if so why,...

    you can still buy unsealed batteries? if so why, i only used sealed agm
  15. Replies
    14
    Views
    327

    if your needing choke to make it run correctly...

    if your needing choke to make it run correctly your going to blow it up...rebuild and clean the carbs properly with oem kits
  16. Replies
    5
    Views
    149

    trim isnt automatic...also 1999 slx was a 1050...

    trim isnt automatic...also 1999 slx was a 1050 not 1200
  17. Replies
    14
    Views
    258

    im looking to do the same

    im looking to do the same
  18. Replies
    17
    Views
    830

    you need old 900 or 1050 stator to use old...

    you need old 900 or 1050 stator to use old cdi....1200 stators are new gen..so updated 1050 cdi work with 1200 stator
  19. Replies
    12
    Views
    1,053

    Getting closer...reeds are in and hot seat...

    Getting closer...reeds are in and hot seat domes...powder coat stuff should be here this week

    https://i.imgur.com/EBc77a8h.jpg

    https://i.imgur.com/ujpADMFh.jpg
    ...
  20. thats all i do is bring them the jugs and pistons...

    thats all i do is bring them the jugs and pistons in the box with the specs and ive never had an issue.
  21. Replies
    31
    Views
    837

    stop messing around and pull the motor out much...

    stop messing around and pull the motor out much easier....use an impact to remove the fly wheel nut, get a universal jet ski flywheel puller an it comes off easy.
  22. i kind of doubt its water, they are designed to...

    i kind of doubt its water, they are designed to have water get in the hull...this is why there is a bilge pump...everything is sealed and water proof...in theory you are basically good till the...
  23. Replies
    7
    Views
    233

    there really is no way around the cost...even...

    there really is no way around the cost...even junk knock offs are expensive...the reality is they are getting harder and harder to find.
  24. good news sort of, hope you get the money back...

    good news sort of, hope you get the money back but probably unlikely knowing are government system.

    no need for silicone if the box has the gasket and is snapped together properly they are water...
  25. Replies
    3
    Views
    161

    why not use the proper stuff its not hard to find...

    why not use the proper stuff its not hard to find or expensive
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4