Search

Type: Posts; User: TJS0712F

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    49
    Views
    1,060

    Thanks for the strainer tip. Question. Did you...

    Thanks for the strainer tip. Question. Did you walk into a NAPA store and say I need a fuel pump strainer for a Kawi 08 Ultra 250X. If I did that here in CT. I would get the deer in headlights look.
  2. Replies
    1
    Views
    65

    Wow. The DEEEP have no clue or know any boating...

    Wow. The DEEEP have no clue or know any boating regulations or laws whatsoever. I used to hang out on Lake Zoar. I have seen the DEEEP boat actually hit another boat and damage it. The DEEEP boat...
  3. Replies
    41
    Views
    1,523

    I can tell you this. If the gauge does not work...

    I can tell you this. If the gauge does not work it will be SLO mode not matter what. My guage was not working when I first took it out this year and it was in SLO mode. When it finally came on the...
  4. Replies
    8
    Views
    215

    Nice build. That thing needs a BBC or SBC and a...

    Nice build. That thing needs a BBC or SBC and a berk pump.
  5. Replies
    21
    Views
    456

    Not sure if we are referring to the same part...

    Not sure if we are referring to the same part here Sean. I am referring to the corroded piece of alum that the OP had welded up not the part with the piston rings on it. I have welded corroded alum...
  6. Replies
    13
    Views
    329

    Same here. No Russian either.

    Same here. No Russian either.
  7. Replies
    13
    Views
    329

    I would like to see pics of this. Interesting to...

    I would like to see pics of this. Interesting to see a fix on this. And not replacing a new crank either.
  8. Replies
    18
    Views
    1,078

    Hard to tell from that pic but I see a lot of...

    Hard to tell from that pic but I see a lot of corrosion. Albeit, I have welded a Yamaha block back together a while back where he was told he needed a block. By the way. JB weld causes havoc when...
  9. Replies
    5
    Views
    145

    Here is how I did it. I used that place in Fla....

    Here is how I did it. I used that place in Fla. for the ring that was mentioned. Keep your wear ring to impeller clearances tight. Mine are .006" currently.
    ...
  10. Replies
    21
    Views
    456

    Here is how I would fix that., YMMV. Cut that...

    Here is how I would fix that., YMMV. Cut that piece with the pin hole off, take note of the location and angle (this is what a small fixture plate is for). Find a piece of pipe or round stock to...
  11. Thanks raven: Here is the link to the OP. ...

    Thanks raven:
    Here is the link to the OP.

    http://greenhulk.net/forums/showthread.php?t=247134
  12. Replies
    12
    Views
    484

    Alum or galvanized. Well the most important thing...

    Alum or galvanized. Well the most important thing to also look for is the axle tube rusting as these are NOT alum. My axle stubs rusted right where they are welded to the axle tube(I have a post on...
  13. Replies
    23
    Views
    320

    That gap looks to be over .100"(100thou.).

    That gap looks to be over .100"(100thou.).
  14. I had too much clearance cause of my crash I had....

    I had too much clearance cause of my crash I had. I welded up the edges of my impeller and machined them down. I have a large post on this. I also replaced my wear ring. Pretty straight forward.
  15. Not sure if the 1200-stxr pump is the same as the...

    Not sure if the 1200-stxr pump is the same as the 12 or 15Fs are but the most critical thing on these pumps is keeping the water out of the bearing housing. Also the second most critical thing is in...
  16. Replies
    4
    Views
    153

    As people say esp Keith Fenner(famous YT...

    As people say esp Keith Fenner(famous YT machinist). I never got angry taking apart something that was slathered in never-size.
  17. What ever happened with this. Did you take them...

    What ever happened with this. Did you take them to the dealer or find the issue yourself.
  18. Replies
    3
    Views
    152

    If you want to part with the broken waterbox let...

    If you want to part with the broken waterbox let me know. I want to cut one apart and do some mods and TIG it back together. PM me.
    T.J.
  19. Replies
    14
    Views
    500

    Forgive me as I come from Big block and small...

    Forgive me as I come from Big block and small block chevy stuff, but when a cam or bearings get wiped out the block comes completely apart and all the oil passages and orifices cleaned and flushed...
  20. Replies
    7
    Views
    247

    The biggest pain is the dangling handle bars. To...

    The biggest pain is the dangling handle bars. To keep them from scratching your machine make sure you put towels down or something.
  21. Replies
    7
    Views
    247

    I used this above post as a guide. The only thing...

    I used this above post as a guide. The only thing was it did not have the "tilt" option. Everything else is pretty much the same.
  22. Replies
    7
    Views
    247

    There is a post on this in the kawi forums with...

    There is a post on this in the kawi forums with pics. I have done this "tightening" a couple of times. Search loose steering on the kawi forums.
  23. Replies
    1
    Views
    101

    Flag Day...CNC Cut Flag

    Got my CNC plasma cutter finally built and wired and now working. I cut 5 flags already. I also cut many other parts for jobs I was doing. Here is a vid of it cutting the stars for the flag and a pic...
  24. Replies
    4
    Views
    225

    I use my large bench vice with alum angle for...

    I use my large bench vice with alum angle for soft jaws. Never had an issue.
  25. Replies
    41
    Views
    1,523

    Maybe he had a super long vacuum hose.

    Maybe he had a super long vacuum hose.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4