Search

Type: Posts; User: steve45

Page 1 of 8 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    1
    Views
    66

    Could be a loose/dirty connection on the ground...

    Could be a loose/dirty connection on the ground connection to the engine, or the battery connection on the relay box. Could be a corroded jet pump liner. Could be a bad starter relay, or a bad...
  2. My pricing estimate was for Kawasaki parts. I...

    My pricing estimate was for Kawasaki parts. I use other brands, myself. You WILL need a spline tool. A shaft holder is nice, I made mine.
  3. If it cranked before (during the compression...

    If it cranked before (during the compression test), it's quite possible that the impeller is binding on the inside of the jet pump. Water gets between the liner and pump housing, causing corrosion,...
  4. Replies
    12
    Views
    213

    As an airplane owner, I have a fondness for...

    As an airplane owner, I have a fondness for safety wire (it is NEVER used to secure hoses on airplanes BTW). I've used stainless safety wire for years to secure oil lines on PWCs. I've used it on...
  5. Replies
    10
    Views
    498

    Did you try hitting the screw on the puller with...

    Did you try hitting the screw on the puller with a brass hammer?
  6. Replies
    1
    Views
    110

    Welcome aboard, John! Do you have the special...

    Welcome aboard, John!

    Do you have the special dongle? This may help: http://greenhulk.net/forums/showthread.php?t=259264

    Do an advanced search for 'program' or 'Immobilizer' and specify to...
  7. It's been 10 days and you haven't opened the...

    It's been 10 days and you haven't opened the electrical box? Water in there, with a +12 volt battery lead will cause corrosion in a heartbeat.

    Open it today.
    If it's got moisture in it, dry...
  8. Replies
    1
    Views
    96

    Welcome aboard, mfshah7! Before doing any...

    Welcome aboard, mfshah7!

    Before doing any repairs, I'd suggest a compression test. And, a service manual.
  9. Replies
    7
    Views
    650

    I wouldn't. It wasn't the dealer's fault, and...

    I wouldn't. It wasn't the dealer's fault, and I'm sure their business has been hurting due to inability to get inventory.
  10. If you want to make a difference, reconsider...

    If you want to make a difference, reconsider shipping rates for small items. There is no reason to charge about $15 (or whatever) for shipping a small gasket, O-ring, or screw that could easily be...
  11. I think most people on this forum probably...

    I think most people on this forum probably rebuild their own jet pumps. You need a couple of special tools. Bearings & seals will probably cost you $100-150.
  12. The 2015 pump is the upgraded one, so no problem...

    The 2015 pump is the upgraded one, so no problem there. You don't have to run in salt water to have corrosion in the pump, and it can happen to other brands as well.

    There have been corrosion...
  13. Replies
    7
    Views
    164

    Is this the 'BR' model? ...

    Is this the 'BR' model? http://greenhulk.net/forums/showthread.php?t=285360
  14. Replies
    1
    Views
    136

    41803 is supposed to be the cutoff, so it looks...

    41803 is supposed to be the cutoff, so it looks like the cheap plugs should work. I have an older igniter somewhere, I'll try to find it and verify the part number.

    UPDATE: The Kawasaki part...
  15. Replies
    5
    Views
    122

    Look on Ebay.

    Look on Ebay.
  16. Replies
    6
    Views
    151

    When you're looking for parts like this, it's...

    When you're looking for parts like this, it's important to get the complete NINE-digit part number. I believe your lever is # 13320-3719.
  17. Replies
    1
    Views
    126

    Welcome aboard, norubit! Sure it can be done! ...

    Welcome aboard, norubit!

    Sure it can be done! That doesn't mean that it will be easy, it will take some work. I'm planning to install a pair of Kawasaki 1500s in my Yamaha Exciter boat.
    ...
  18. Get rid of the fuel pickups, you don't need...

    Get rid of the fuel pickups, you don't need strainers in the tank when you've got an inline filter (and a filter inside the carb). Put a piece of fuel hose on each pickup to give the proper lengths...
  19. Replies
    15
    Views
    458

    What you're trying to determine is the pressure...

    What you're trying to determine is the pressure that will open the needle valve. You do this with the carb disassembled. You're only testing the needle valve and spring. It helps if you put a drop...
  20. On the 'Skis with the Immobilizer keys, the pump...

    On the 'Skis with the Immobilizer keys, the pump kicks on for several seconds whenever you insert the key, or bump the starter. When my 'Skis have been sitting for a while, I let the pump run 2 or 3...
  21. Replies
    4
    Views
    119

    Try pulling the choke out halfway and see if that...

    Try pulling the choke out halfway and see if that helps. For grins, you might richen the low speed mixture screws a 1/4 turn and see what happens.

    That said, if you don't know when the carbs...
  22. Replies
    15
    Views
    458

    You're pressuring the whole thing up to 40 PSI?...

    You're pressuring the whole thing up to 40 PSI? :facepalm:
  23. Replies
    8
    Views
    1,611

    Ebay. 1/8" ID. 7/64" is also good.

    Ebay. 1/8" ID. 7/64" is also good.
  24. No resources on backflushing the fuel filter,...

    No resources on backflushing the fuel filter, just pull it out and pump some solvent through it in the backwards direction. Let it dry before re-installing.

    White smoke is most likely steam,...
  25. Replies
    4
    Views
    220

    Cast aluminum. ...

    Cast aluminum.

    https://www.partzilla.com/catalog/kawasaki/jet-ski/2016/ultra-310x-jt1500lgf/cylinder-piston-s
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4