Search

Type: Posts; User: dnielsen

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. I just replaced my oil cooler for the same...

    I just replaced my oil cooler for the same reason, problem solved.
  2. Thread: Egt vs afr.

    by dnielsen
    Replies
    34
    Views
    7,343

    Love the triple O2s, I would like to see the AFRs...

    Love the triple O2s, I would like to see the AFRs on a stocker on all three cylinders for comparison. I've often suspect that the #3 hole runs leaner..........
  3. Get the next size up Torx socket and pound it in...

    Get the next size up Torx socket and pound it in there till it bottoms. Get a propane torch and heat the plug a bit and then you can remove it. Been there done that!
  4. Replies
    87
    Views
    17,109

    +1, got about an hour on mine and done for the...

    +1, got about an hour on mine and done for the season. If it blows I'll try the Fizzle IC 1000 next. Haven't seen any complaints on those yet.........
  5. Replies
    14
    Views
    2,288

    Red is always faster than yellow, good swap!

    Red is always faster than yellow, good swap!
  6. Replies
    9
    Views
    3,787

    The kit that Fizzle posted is a great deal...

    The kit that Fizzle posted is a great deal compared to buying just the Riva G3 IC. His kit comes with everything needed for your application with exception to the resonator delete kit which you have...
  7. You won't get a lot of good post about "the New...

    You won't get a lot of good post about "the New Torx" other than a few cheerleaders because most on the forum that stay in the know about them have seen horror story after horror story with Torx...
  8. I'm not real sure what hull they are talking...

    I'm not real sure what hull they are talking about.
  9. Which kit, catch can or air intake? Why will it...

    Which kit, catch can or air intake? Why will it not fit, just asking have never looked at a suspension ski.



    you are welcome!

    This is the catch can you will need...
  10. Found these a while back, thought about trying a...

    Found these a while back, thought about trying a few. You will need to sort through the site to find the valves that would work in our application, 1" valves are available and looked promising.
    ...
  11. Post #82 shows some pics of a Riva plate that has...

    Post #82 shows some pics of a Riva plate that has been ground down to fit. The idea is to take only enough metal off the top to get the plate to flush on the bottom with the hull.
    ...
  12. Good point Jerry, I tend to forget most forum...

    Good point Jerry, I tend to forget most forum member still run the stock air intake systems without the catch can. After reading your post I remembered having the same oily film in mine before...
  13. +1, sounds like SC seal, need to replace it with...

    +1, sounds like SC seal, need to replace it with the Viton seal. OEM seal can't handle the heat.......
  14. The wedge is not your problem, again did you fit...

    The wedge is not your problem, again did you fit the plate or simply bolt it up?
  15. I've been running the Riva plate at 80+ for three...

    I've been running the Riva plate at 80+ for three years or at least since the first batch went out with the setup in my sig, wot with throttle chops a 1000 times, slow rollers, etc. etc with no...
  16. Removing the Riva plate is not the solution, JP...

    Removing the Riva plate is not the solution, JP ran the plate up to 88 mph. Did you fit the plate or simply bolt it up? The plate needs to be dry fitted, removing material from the front top side...
  17. Awesome results!

    Awesome results!
  18. Replies
    101
    Views
    9,866

    The last pic posted is an oil pump and not the...

    The last pic posted is an oil pump and not the regulator but doesn't matter as far as resolving the problem. Oil looks good in the pictures, I say change the oil and filter and go ride a tank of fuel...
  19. Replies
    101
    Views
    9,866

    Any water in the oil?

    Any water in the oil?
  20. Replies
    8
    Views
    1,007

    Take some pics of the damaged SC if you have...

    Take some pics of the damaged SC if you have pulled the housing on it and post pics, just curious to see how much metal the engine may have ate. It's llikely you found your noise in the SC, if it's...
  21. Replies
    5
    Views
    1,286

    Most guys just bend the squirter......

    Most guys just bend the squirter......
  22. Replies
    13
    Views
    2,593

    Pull the seat off and give it a short ride to see...

    Pull the seat off and give it a short ride to see if you can tell where it's coming from, likely the carbon seal.
  23. Replies
    7
    Views
    1,054

    The back of the plate is cut to produce more bow...

    The back of the plate is cut to produce more bow lift thus reducing drag on the hull resulting in speed gains. Also improves straight line handling at higher speeds. It can be a bit of a chor to fit...
  24. Replies
    8
    Views
    1,007

    Pull the SC intake hose and see of it spins free,...

    Pull the SC intake hose and see of it spins free, also pull SC output hose to check for debris. Check the pump for anything lodged. Valves are good by what you described. Not sure what type noise you...
  25. Replies
    8
    Views
    1,007

    Check the supercharger, could also be sheared...

    Check the supercharger, could also be sheared flywheel bolts, a dropped valve into the cylinder. Hopefully none of this is the case.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4