Search

Type: Posts; User: 2fast4u

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    41
    Views
    3,252

    this problem occurs when the ski is not flushed...

    this problem occurs when the ski is not flushed properly after salt water use and corrosion of the casting of the head cooling passages occurs.
  2. Replies
    41
    Views
    3,252

    Here is a thought wonder what % of skis with...

    Here is a thought wonder what % of skis with cracked heads were used in salt water verses those that were ONLY used in freshwater? The reason I am think of this is that the salt water eats away the...
  3. Thread: YES renewal

    by 2fast4u
    Replies
    6
    Views
    263

    There might be a third party warranty company you...

    There might be a third party warranty company you could buy more warranty for your ski. But I only recommend the OEM factory warranty. I have heard horror storys from folks who purchased third party...
  4. Thread: YES renewal

    by 2fast4u
    Replies
    6
    Views
    263

    no

    no
  5. Replies
    24
    Views
    997

    sorry to here the news, looks like you may have a...

    sorry to here the news, looks like you may have a cracked head.
  6. Replies
    24
    Views
    997

    re glue plastic cam guide on valve cover then...

    re glue plastic cam guide on valve cover then you a good to go just keep a check on dip stick oil for milky look on oil if you don't see any problems you should be good to go.
  7. Replies
    24
    Views
    997

    they are cam top saddles that help hold the cam...

    they are cam top saddles that help hold the cam in place. they are part of the head and are align bored on the head for the cam top cap plate. this part comes with the head and can not be purchased...
  8. Replies
    24
    Views
    997

    More than likely K447 is spot on, there is always...

    More than likely K447 is spot on, there is always a lot of condensation in these motors going from cold to just warming up and then stopping the engine. A motor needs to be run at engine/oil...
  9. Replies
    41
    Views
    3,252

    Allowing these motors to idle for three to four...

    Allowing these motors to idle for three to four minutes prior to shutting them down is a good idea, especially since all the block/head water drains out after the motor is shut down . I always run my...
  10. Replies
    7
    Views
    404

    If you think your ecu is bad ask around and see...

    If you think your ecu is bad ask around and see if you can borrow a known good ecu from another ski same model and test it on your ski. Then you will be 100% sure it is the ecu. Just my 2 cent worth...
  11. that looks good, but I use my trim a lot under...

    that looks good, but I use my trim a lot under power and need to leave the trim sleeve on for leverage .
  12. that works good for late model skis but my ski...

    that works good for late model skis but my ski has a manual trim on the left side and the left grip has to be larger to fit over the trim sleeve .
  13. Replies
    20
    Views
    1,487

    unless you are a expert tuner and have all the...

    unless you are a expert tuner and have all the gauges/data to make sure your tune is correct I would stay away from the self tune and just use one of there time tested tunes from Riva or Dean. A...
  14. suggestions for replacement handle bar grips?

    2009 Fzr with stock oem handle bars. Looking for suggestions on replacements grips for my ski. What are you guys using? Thanks for your reply.
  15. Replies
    14
    Views
    761

    it does not matter what pump size you have, the...

    it does not matter what pump size you have, the fuel pressure regulator is what controls the final fuel pressure at the injectors. you need a fuel pressure gauge after the regulator where the fuel...
  16. Replies
    11
    Views
    595

    Your modified Riva SS grate looks to be the best...

    Your modified Riva SS grate looks to be the best for rough water use. If top speed on calm water is what you are lookin for then find a R&D grate there should be 1 to 2 mph difference in these two...
  17. Replies
    11
    Views
    595

    the dean,s grate looks like the two out side...

    the dean,s grate looks like the two out side wings on the center bars of the grate are completely even with the front of the scoop wing, where the stock one the wings do not go down a much as the...
  18. Replies
    11
    Views
    595

    can some post a picture of a un modded Riva...

    can some post a picture of a un modded Riva stainless grate for comparison?
  19. Replies
    11
    Views
    595

    post pictures of grate please.

    post pictures of grate please.
  20. Replies
    9
    Views
    246

    never heard of that. WHY will a agm battery...

    never heard of that. WHY will a agm battery damage that stuff? To high of voltage or that battery requires a higher voltage to keep it charged . ??????????????
  21. yes but the cruse control function will NOT work.

    yes but the cruse control function will NOT work.
  22. Thread: Water in hull

    by 2fast4u
    Replies
    33
    Views
    3,653

    My ski is totally dry inside after a 120 mile...

    My ski is totally dry inside after a 120 mile river ride, no water at all, if there is water in your ski you have a leak unless you take water in around the seat, handle bars or front cowl . 350+...
  23. Replies
    9
    Views
    462

    100% CORRECT this is why these skis are hard to...

    100% CORRECT this is why these skis are hard to start the first time after sitting for months.
  24. Replies
    8
    Views
    421

    replace sparkplugs re test first

    replace sparkplugs re test first
  25. Replies
    64
    Views
    3,195

    I think the machine work charges were $75.00 It...

    I think the machine work charges were $75.00 It was done to reduce the rotational weight so the clutch rpms would slow down faster when the clutch sprag un locked from the supercharger this helped...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4