Search

Type: Posts; User: WaveChaser

Search: Search took 0.00 seconds.

  1. I measured the fuel pressure at each carb and at...

    I measured the fuel pressure at each carb and at the return before the restrictor.
    Mag: 3 psi and goes to 3.5 when goosing on trailer
    Center: 4 psi and goes to 4.5 when goosing on trailer
    PTO: ...
  2. So had time to install them as Ripcuda described....

    So had time to install them as Ripcuda described. I still have the PTO and Center cylinders spark plugs aluminum color and Mag nice and wet at 3300 rpm. Low carb adjust are at 2 turns out. I am...
  3. I agree. Is there a procedure for...

    I agree. Is there a procedure for aligning/mounting the carburetors? Even though if I align them up via the paint marks on the screws holes in the rail, they just don't drop in. Should they be...
  4. Yes, I installed the manifold and torqued it...

    Yes, I installed the manifold and torqued it before torquing the jugs.

    i preformed the leak down test. After 10 minutes it dropped 1 in hg. After 1hr8min it only dropped 3.5 in hg.

    If you...
  5. Is RTV or some sealant needed for the jug...

    Is RTV or some sealant needed for the jug gaskets? A friend of mine uses marine grease on them to re-use them and he never has any issue of leaks.
  6. I dont believe it is the fuel system. I have...

    I dont believe it is the fuel system. I have beat that and tested it to death.

    An air leak is my issue somewhere. When I installed the jugs, I did not have the manual at that time. It says to...
  7. Only doing what the Polaris manual says. I have...

    Only doing what the Polaris manual says. I have changed the fuels switch with a new one.

    I have had the carbs apart at least 10 times now. I tested the popoff pressure once again. I get between...
  8. I found in the Polaris manual how to test for...

    I found in the Polaris manual how to test for leaks in the fuel system on page 3.106 entitled "Fuel Line Air Leak Testing". Basically you disconnect from the pump and tank. Plug one end and fill...
  9. K447, What can you do about the fuel sender if it...

    K447, What can you do about the fuel sender if it is leaking? I heard it was pressed in with gas resistant epoxy. So none of this makes sense. Like I said I put a 19gal/hr 12v DC electric pump...
  10. I started out with clear. It is pretty stiff and...

    I started out with clear. It is pretty stiff and you cannot pinch it shut with your hand. So then I purchased some really stiff fuel line that is rubber inside and nylon outside. I have changed to...
  11. I still have not figured this ski out. One thing...

    I still have not figured this ski out. One thing I noticed was the water separator was not filling full so I cleaned and replaced the Oring. I took the separator, plugged the out and tested it in a...
  12. With all three plugs running an aluminum color...

    With all three plugs running an aluminum color and dry just riding the ski around for a minute or two, it is running super lean and I am going to burn up the top end. This thing is starving for gas...
  13. I am getting nowhere with this ski. I have gone...

    I am getting nowhere with this ski. I have gone through the fuel system and totally rebuilt everything:

    rebuilt carbs
    installed and rebuilt tripple output fuel pump
    installed new gas valve...
  14. The jets are 102.5 mains as it only said to...

    The jets are 102.5 mains as it only said to replace them. From what I read you start at the "stock settings" and then turn out 1/4 turn, run and check the plugs to see if they are chocolate brown...
  15. Wow. Nobody?

    Wow. Nobody?
  16. 1995 750 SLT Snorkel intake modification and triple output fuel pump install

    This has been a two year project as I have not had a lot of time to mess with this ski. This ski when I purchased it had the single outlet fuel pump and snorkel intake. I purchased the modern...
Results 1 to 16 of 16