Search

Type: Posts; User: raiderteen

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    83

    Personally, I think I would've used the Yamalube...

    Personally, I think I would've used the Yamalube until 10hr service. But that being said, I doubt you will have any issues keeping that in it.
  2. Replies
    4
    Views
    83

    By oil amplifier are you meaning like a oil...

    By oil amplifier are you meaning like a oil additive? I wouldn't think you would need anything special in the oil. It isn't like the old school hydraulic flat tappet cams in a small block chevy that...
  3. One thing to remember, out of the water the...

    One thing to remember, out of the water the engine will be idling at a higher rpm then it will while in the water. It will also rev easier, quicker, and "healthier". The true test will be once you...
  4. Replies
    34
    Views
    488

    Do you happen to have one of the in-line spark...

    Do you happen to have one of the in-line spark testers? These can be used to rule out bad spark plugs and sometimes even weak coils. I've seen new plugs be bad before.
  5. https://www.manualslib.com/products/Yamaha-Wb760-W...

    https://www.manualslib.com/products/Yamaha-Wb760-Waveblaster-760-8661121.html
  6. I have no preference on polishing compounds. But...

    I have no preference on polishing compounds. But 3M and Meguiars make good products from experience.

    Check this out for the fitting and OEM Part number....looks like its called a Pilot, Water...
  7. For the paint polishing. Try a light cutting...

    For the paint polishing. Try a light cutting polishing compound to try and bring life back to the paint. Possibly the same for the over spray area.

    For that thru hull fitting, I am sure you can...
  8. Very clean ski! Don't see too many in that shape...

    Very clean ski! Don't see too many in that shape anymore for sure. I can see now why you want to keep it as close to original as possible.
  9. I think that's what I would do. Order and hope...

    I think that's what I would do. Order and hope for the best. If it ends up unavailable they will refund your order. Let us know how it goes!
  10. Replies
    34
    Views
    488

    Correct spark plugs are BPR8ES. I've seen what...

    Correct spark plugs are BPR8ES. I've seen what appeared to be brand new plugs not spark before. Replaced and got spark back.
  11. I cant say for certain on availability. I ordered...

    I cant say for certain on availability. I ordered some OEM Oil tank brackets for my 1999 Yamaha LS2000 jetboat from partzilla. They were discontinued as far as I am aware and it took 2 weeks for them...
  12. Replies
    11
    Views
    542

    Pull it. Rebuild it. Enjoy summer. They aren't...

    Pull it. Rebuild it. Enjoy summer. They aren't complicated rebuilds and you will know them inside and out. Do carb rebuilds while its apart using ONLY genuine Mikuni rebuild kits.
  13. You can probably find seat covers from one of the...

    You can probably find seat covers from one of the aftermarket suppliers. Usually equal or better quality than OEM as well. For the bumpers, have you looked on OEM Parts finder sites? Ebay too but...
  14. Not sure if the IR kit is any different then Jet...

    Not sure if the IR kit is any different then Jet Works but found this with google.



    http://greenhulk.net/forums/attachment.php?attachmentid=12736&d=1166575714
  15. Replies
    11
    Views
    542

    Those cylinders (if original) and pistons are all...

    Those cylinders (if original) and pistons are all aluminum with Nikasil Coating. Good chance any rust/corrosion you see will come off very easily and not need any honing (special honing required for...
  16. Replies
    33
    Views
    1,782

    As I said, there is a huge difference between...

    As I said, there is a huge difference between some short speed runs and WOT for "miles on end" and "as long as possible". Yeah these skis with the stage 2 kit are pretty solid. But what the OP is...
  17. Replies
    33
    Views
    1,782

    There's a big difference between running a couple...

    There's a big difference between running a couple miles WOT then cruising and running for "miles on end" or "as long as possible" at WOT without letting off once. I don't care what brand, any...
  18. Replies
    11
    Views
    542

    Compression numbers will be inaccurate (read...

    Compression numbers will be inaccurate (read high) with any significant amount of liquid in the cylinders. (Less available volume=higher compression).

    You should be looking for 115-130 range on...
  19. Replies
    25
    Views
    1,349

    Southern IL about 2 hrs from St. Louis (South...

    Southern IL about 2 hrs from St. Louis (South East)


    Furthest customer yet was a guy last spring from Oklahoma (who had a summer place near the Mississippi river). He brought a pair of Ultra...
  20. Replies
    25
    Views
    1,349

    Total bill was ~ $1750. Including oil change, new...

    Total bill was ~ $1750. Including oil change, new crank adapter, new driveshaft, associated seals, engine alignment, reverse kit, 90hp tune. Labor was less than parts cost. His dealer wanted at least...
  21. Replies
    25
    Views
    1,349

    The driveshafts allow for some "play" but...

    The driveshafts allow for some "play" but obviously not that much movement. I honestly don't understand how this one lasted just over 100 hours as it was. I saw no signs of loose engine mounts or...
  22. Replies
    25
    Views
    1,349

    Got the shims for free (not counting my previous...

    Got the shims for free (not counting my previous cost of the aluminum). When I got there and compared to a factory shim there was a issue with how their cnc converted the file I gave them. They were...
  23. Replies
    25
    Views
    1,349

    I don't have access to a jigsaw suitable for this...

    I don't have access to a jigsaw suitable for this work. But that would certainly be another way to do them as well. Seeing as I needed a minimum of 16 made (at 1/16" each) it made sense to have them...
  24. Replies
    25
    Views
    1,349

    Factory shims are most likely stamped. The ones I...

    Factory shims are most likely stamped. The ones I am having made are cut on a CNC plasma table and then deburred/cleaned up
  25. Replies
    25
    Views
    1,349

    I didn't make the alignment plate. Was cheap...

    I didn't make the alignment plate. Was cheap enough to just purchase it outright. I paid $45ish for it shipped. Already owned the main Seadoo alignment kit.

    Hoping to get a call today saying the...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4