Search

Type: Posts; User: tiderider

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    94

    If you have a candoo, you can test each injector...

    If you have a candoo, you can test each injector for function.. It can be wiring/connections or ECU.
  2. Replies
    2
    Views
    80

    Either a bad head gasket or oil cooler.. Any...

    Either a bad head gasket or oil cooler.. Any coolant mixing with the engine oil?
  3. Replies
    3
    Views
    244

    I can say that WSM bearings are good. I installed...

    I can say that WSM bearings are good. I installed a full set and clearances were perfect.
  4. Replies
    16
    Views
    502

    I'm pretty sure not all Siemens ECU can be...

    I'm pretty sure not all Siemens ECU can be tuned.. I have many logs to prove so..
  5. Replies
    16
    Views
    502

    I wouldn't waste your money trying to tune an...

    I wouldn't waste your money trying to tune an older Siemens ECU... No one can.. From my experience it was a 2007.
  6. Replies
    22
    Views
    496

    Tap on the retainers with the back handle of a...

    Tap on the retainers with the back handle of a hammer. You should hear the valve go in sligthly, it may take 2 tries sometimes. The single groove keepers make this much simpler.
  7. Replies
    15
    Views
    642

    That impeller bolt is part of the oil pump shaft,...

    That impeller bolt is part of the oil pump shaft, probably a good idea to replace as well.
  8. Replies
    22
    Views
    496

    Just tap on the valve stem's top a few times and...

    Just tap on the valve stem's top a few times and then try removing. Works every time.
  9. Replies
    22
    Views
    496

    Clean the threads on the crankshaft with a...

    Clean the threads on the crankshaft with a contact of some sort so the loctite sets fully when you install the flywheel bolts.
  10. The opening on the cylinder head for this nipple...

    The opening on the cylinder head for this nipple is 5mm. Hose is 1/4 inch.. Any guess to where they can be purchased as aftermarket?
  11. Thread: Engine Paint

    by tiderider
    Replies
    7
    Views
    338

    Its all about the prep work. I used Rustoleum...

    Its all about the prep work. I used Rustoleum high temperature with the mat black option. Holds strong now for years.
  12. Replies
    0
    Views
    63

    2007+ OEM 4tec valves issues?

    Any issues with the newer seadoo 4 tec valves from 2007+? Would they be okay to spin up 8600Rpms if stock sprigs are used with titanium retainers?
  13. FS - Parts Hi, Can you pm me about the Air intake manifold?...

    Hi, Can you pm me about the Air intake manifold? Thank you
  14. Replies
    4
    Views
    190

    SOLD Now those can't be good... Unless they are...

    Now those can't be good... Unless they are ARPs....
  15. Replies
    4
    Views
    190

    SOLD ARP Head studs

    Does anyone have a good clean set of ARP head studs kicking around for the seadoo 4 tec engines?
  16. Replies
    12
    Views
    381

    Yes the cylinder head can be removed without...

    Yes the cylinder head can be removed without pulling the engine.. It probably caused damage to the piston as well..
  17. Replies
    7
    Views
    336

    I did return a full set of Connection rod bolts...

    I did return a full set of Connection rod bolts back to SBT in the past.. 2 of the 6 bolts were cross threaded, they wouldn't screw in by hand.
  18. Replies
    7
    Views
    336

    I installed a complete set of WSM bearings for...

    I installed a complete set of WSM bearings for $104 Usd... (Main bearings, counter balance bearings, connecting rod bearings and all half ring thrust bearings) Clearance were all good as well with...
  19. Replies
    23
    Views
    648

    I would try finding a newer block. It looks like...

    I would try finding a newer block. It looks like the thrust washer ate far to deep into the block. It will give you issues with the main bearing clearances..
  20. Non supercharger Stator/timing housing for supercharged applications.

    Curious to know if anyone has machined out the block/cap on non supercharged Stator/timing covers so it can be used for supercharged applications?
  21. Replies
    13
    Views
    390

    I was recommended to use 60s or 80s for a...

    I was recommended to use 60s or 80s for a ET137+4mm for a riva tune and Siemens ECU.. Wondering if the 50s would cause less starting issues (Flooding engine) when trying to start the engine hot??
  22. Replies
    23
    Views
    648

    Not checking clearances is 99% of the time why...

    Not checking clearances is 99% of the time why rebuild engines fail.. Especially with the high reving 4 tecs.
  23. Replies
    23
    Views
    648

    Are you referring to installing the half rings?

    Are you referring to installing the half rings?
  24. My coolant hose from the cylinder head always...

    My coolant hose from the cylinder head always leaked with worm clamps.. The T-bolt clamp stopped the leaking issue permanently... The worm clamps also chew into the hoses. AWAB clamps work much...
  25. Replies
    3
    Views
    227

    Does anyone know what type of paint or coating...

    Does anyone know what type of paint or coating methods are used within/around the water impeller surface areas..? The typical smooth black painted areas where the coolant flows around on it?
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4