Search

Type: Posts; User: Bombarusa

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    281

    Yes, the new pump comes with all new bearings,...

    Yes, the new pump comes with all new bearings, seals and o rings. The only items that need to be swapped over are the metal spacer on the impeller side and the washer,nut, spacer and nose cone from...
  2. Replies
    2
    Views
    281

    SVHO impeller shaft removal tips

    Hey everybody I'm getting ready to transfer my 2019 impeller shaft into my new 2020 pump housing and I was just hoping for any tips/pitfalls for getting the old shaft/bearings out of the old housing....
  3. Replies
    4
    Views
    430

    FS - Parts How many hours on the clutch?

    How many hours on the clutch?
  4. Replies
    81
    Views
    16,095

    I am also hoping for clarification directly from...

    I am also hoping for clarification directly from Jerry on this as I have ordered the new pump largely based on the fact that it is supposed to be a true 160mm and may help with...
  5. Replies
    11
    Views
    1,130

    I was planning on upgrading to a dual impeller...

    I was planning on upgrading to a dual impeller when I added my new Fizzle intercooler so I could eliminate the cavitation out of the hole and increase acceleration but when I spoke to Deans Team...
  6. Follow up so far...... JAE is the brand of plug...

    Follow up so far...... JAE is the brand of plug (Japanese Aviation Electronics) and the PBT looks like the material is made from (Polybutylene Terephthalate)....... still can't find the 44 pin GF 80...
  7. So I got back in to my ski to check that plug for...

    So I got back in to my ski to check that plug for you....on the front face of the plug in tiny letters it says: PBT-GF80 < JAE A. I did a quick search and that specific plug number...
  8. Sorry I haven't been on the forum in a while...

    Sorry I haven't been on the forum in a while since it's 12 degrees and snowing here in upstate New York but i will brush the snow off my ski when i get home and see if i can get that plug cover off...
  9. Replies
    3
    Views
    538

    Should be the smaller one......the stock cone is...

    Should be the smaller one......the stock cone is just shy of 3"
  10. I just looked on my "new-to-me" 2019 GP 1800 and...

    I just looked on my "new-to-me" 2019 GP 1800 and both plugs read as follows:
    In large letters: 6EMO
    >PBT-GF39 <

    In small letters in corner: NF1...
  11. Replies
    2
    Views
    574

    FS Would you sell the black strip that fits into the...

    Would you sell the black strip that fits into the middle of the bumpers? (both sides) if so how much? Thanks
  12. Replies
    20
    Views
    6,122

    Wow that looks awsome!

    Wow that looks awsome!
  13. Replies
    57
    Views
    5,431

    I know what you mean...... I definitely think in...

    I know what you mean...... I definitely think in my friends case it was lower than required octane BOTH times. I recall him telling one time that he thinks the ski should still run "fine" on lower...
  14. Replies
    57
    Views
    5,431

    Unfortunately it has happened twice so far on my...

    Unfortunately it has happened twice so far on my buddy's '17 310. (I think due to low octane) He bought a '18 RXT while it was down and now uses the ultra as a back up.
  15. Replies
    190
    Views
    23,889

    4-Stroke Nice job Robert. Sounds like a beast!

    Nice job Robert. Sounds like a beast!
  16. Replies
    11
    Views
    1,557

    437276 I am also filling in the voids on my...

    437276
    I am also filling in the voids on my stock intake grate while I'm at it. The small voids on the top I am filling with silicone, then will cut flush with a razor and the large voids on the...
  17. Replies
    11
    Views
    1,557

    Yeah I saw your video, that was really smart!...

    Yeah I saw your video, that was really smart!
    Reaper: Yes I think either 3m 4200 or 5200 should work fine
  18. Replies
    11
    Views
    1,557

    Poor transom plate sealant!

    This is why you should re-seal your transom plate! I have been meaning to do this along with bore matching/trueing the transom to the pump but have been to "busy" and have been taking any free time...
  19. This was a great ride! My wife had an excellent...

    This was a great ride! My wife had an excellent time and were glad to be apart of it. Thanks to everyone who made it possible!437040437041437042437043437045
  20. Replies
    4
    Views
    1,183

    Nice! I should have posted on here before the...

    Nice! I should have posted on here before the ride to see if anyone was going but my wife and I weren't sure if we could make it until last minute. The actual ride was a little short but we ended up...
  21. Replies
    4
    Views
    1,183

    Can-Am ride in Buffalo NY

    436907436908436909436910436911436912
    Just wanted to post some picks from great day we had at the Can-Am ride yesterday in Buffalo NY. We had a beautiful day, got to make a bunch of new freinds, met...
  22. My wife's 2018 VX Cruiser HO back seat clicked...

    My wife's 2018 VX Cruiser HO back seat clicked right on to my 2017 GP 1800 and vise versa.
  23. Hey Sblovat did you ever end up working on this...

    Hey Sblovat did you ever end up working on this ultra? I tried getting a hold of you but never heard back......anyway the offer still stands!
  24. Replies
    63
    Views
    5,140

    Mr gp does bring up a good point about...

    Mr gp does bring up a good point about elevation... I ride at 1500 ft so I am down approx 13hp on my gp 1800 and 9hp on my wife's vx cruiser. It doesn't sound like allot but it can add up to a few...
  25. I agree..... I have pretty much the same set up...

    I agree..... I have pretty much the same set up ad you minus the intake grate and pro cooling and I'm hitting 8620 rpm and 81-83 mph. I am also using Deals tune but you should be closer to that range.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4