Search

Page 1 of 16 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    81,377
    Views
    5,572,553

    if im not mistaking Bryan,that was the agreement...

    if im not mistaking Bryan,that was the agreement between you and Jerry for letting you back on the site....
    to stay out of this section wasnt it???
  2. Replies
    10
    Views
    934

    You need a torque wrenc,holding plate and gear...

    You need a torque wrenc,holding plate and gear holding tool to do it right and most accurate..BUT you can do it in the ski if you have a torque wrench that can record highest slip by locking the...
  3. Replies
    229
    Views
    24,487

    Your gonna have to Jerry.....Evan is a little to...

    Your gonna have to Jerry.....Evan is a little to fragile to handle that much power.....:shock: :-k #-o :lol::lol:
  4. Replies
    63
    Views
    3,263

    Correct....Common sense just got thrown out the...

    Correct....Common sense just got thrown out the window along time ago and now I can see it has carried on over here........Thats the problem with society now a days..Wether it makes sense or not......
  5. Replies
    13
    Views
    2,354

    Correct....Lets not let this turn into a place to...

    Correct....Lets not let this turn into a place to indirectly sell off the parts through PMs..If so you will leave me no choice but to remove your thread..Thanks and have a nice day
  6. Replies
    9
    Views
    1,885

    Check and make sure the impeller wheel on the...

    Check and make sure the impeller wheel on the Scer isnt spinning on the shaft.....Torque that nut down to 25Ft lbs as long as you have the SCer out...
  7. Replies
    21
    Views
    1,681

    Exactly......Why was the motor rebuilt with only...

    Exactly......Why was the motor rebuilt with only 102 hours on the ski...Something obviously let go.....AND was it rebuilt or replaced??IF it was replaced by an SBT motor i would run from this...
  8. Replies
    21
    Views
    1,681

    You are correct..Super charger service is 436.00...

    You are correct..Super charger service is 436.00 from Jerry(Mr.Greenhulk) YOu cannot go wrong as Jerry is the best in the buisness and will NOT screw you...He uses only Seadoo OEM parts and has...
  9. Replies
    21
    Views
    1,681

    Welcome to Greenhulk......$4500.00 doesnt sound...

    Welcome to Greenhulk......$4500.00 doesnt sound like a bad price to me....I would be really concerned about Supercharger service....Is do to be rebuilt seeing its at 100+ hours....They are...
  10. Thread: 2004 RXP H Temp

    by Snoman
    Replies
    6
    Views
    1,053

    Check the coupler that connects the J-pipe to the...

    Check the coupler that connects the J-pipe to the water box,make sure you did not tighten the coupler over the j-pipe pissers... Also make sure the J-pipe is aligned and NOT butted up against the...
  11. Replies
    29
    Views
    2,368

    FS Let me get this straight.....You bought a MPEM...

    Let me get this straight.....You bought a MPEM from Mr.Stang....Claimed it was defective,didnt work BUT was cosmetically in regular condition....You ship it back..You claim it gets damaged in return...
  12. Replies
    32
    Views
    14,789

    OK boys....I just wasted a half hour of my like...

    OK boys....I just wasted a half hour of my like reading and deleting 60 posts of BS......Im asking you guys nicely to keep the thread on topic...I dont care who has the biggest dick in chop...This...
  13. A set of bearings are $50.00....Also take into...

    A set of bearings are $50.00....Also take into consideration that the front oil seal is probably not in the best of shape after sitting for all these years......IF this were me I would spend the 50...
  14. Replies
    75
    Views
    7,026

    mine and mommas......

    mine and mommas......
  15. Thread: Cracked coil

    by Snoman
    Replies
    11
    Views
    1,684

    You can use 1 inch shrink tubing too.....

    You can use 1 inch shrink tubing too.....
  16. Replies
    81,377
    Views
    5,572,553

    So which is it??? Did you come on this thread to...

    So which is it??? Did you come on this thread to participate or start shit???If it's ride plates and top speed your after then my friend you are in the wrong place and if I may, I'll ask you nicely...
  17. Replies
    27
    Views
    4,284

    anytime brother.....I know when i ran it with the...

    anytime brother.....I know when i ran it with the J pipe i had to cock things around..it wasnt that bad then..BUT the 08 setup is alot bigger and by adding 2 more inches to the manifold puts the...
  18. Replies
    5
    Views
    701

    I use a tiny dab of red....Don't get carried away...

    I use a tiny dab of red....Don't get carried away because if you get any inside you could lock up the spring and check ball..
  19. Replies
    16
    Views
    9,039

    If you have the fuel pump assembly out,why would...

    If you have the fuel pump assembly out,why would you only recommend replacing just the 1 filter???

    IF this were me,And I was going to go through all the trouble of taking the assembly out i would...
  20. Replies
    30
    Views
    3,997

    FS Love this gauge pod...Run it on both my...

    Love this gauge pod...Run it on both my skis.....Great addition for the older style skis...
  21. Replies
    11
    Views
    1,267

    I use the HT MOTO 6 liter hand pump oil...

    I use the HT MOTO 6 liter hand pump oil extractor....Jerry sells them too if im not mistaking....


    https://www.4-tecperformance.com/index.php?main_page=product_info&cPath=87&products_id=864
  22. Replies
    17
    Views
    1,665

    Electrical sucks........

    Electrical sucks........
  23. Replies
    11
    Views
    1,480

    John, That plug is capped off on most all 08+...

    John,
    That plug is capped off on most all 08+ midpipes...It is threaded into the water jacket so you cannot,and do not want to use that for your 02 sensor......Your going to want to want to drill...
  24. Thread: Injector advice

    by Snoman
    Replies
    4
    Views
    753

    IF your running the CMD with auto tune,Then i...

    IF your running the CMD with auto tune,Then i would go with these 80s....Use the CMD/autotune to get your AFRs were you want them...THEN if you decide to upgrade,you will already have enough fueling...
  25. Replies
    19
    Views
    3,050

    06 also used hex head bolts on thier...

    06 also used hex head bolts on thier Scers...First year they used them..
Results 1 to 25 of 400
Page 1 of 16 1 2 3 4