Search

Do you have a spare voltage regulator from the parts ski?http://greenhulk.net/forums/attachment.php?attachmentid=470074&stc=1

http://greenhulk.net/forums/showthread.php?t=289468

I would also love a "wire in resistor" mod/solution for removing Ride..

http://greenhulk.net/forums/showthread.php?t=49805

Why not..???
I love my wedge and 5° nozzle

At Least you found the problem ..Nice

Want to find out if the seal popping from over greasing is a real thing or fake news like yami holding rpm's back till 5-10 hours..

Over greasing the mid-shaft housing - And hearing Stories of seals being pushed out..


Has anybody First hand over greased to the point of pushing the back seal out??


I have put about six...

I am betting yes, because my stock (non trim equipped) ecu moves the trim around when I switch between F-N-R....

I never tried to swap displays- Looks like a pain in the ass, and I have speakers...

Yup.. I will say this, if you open up the manual to a certain page it shows a dial indicator in hole 3 and something about hole 1-- So if you only look at that 1 page/diagram your toast,, But if you...

EX's dont have intermediate housings like the rest of our skis.
the shaft stays in the craft/pump area and the pump/prop housing comes out with no shaft.
There is a DAMPER on the shaft that stays...

I just did that for the photo, normally it has the seat on and strap goes around frame back to strap
My fav test is put 1 dollar bill on top of each bunk-under hull next time you tow with angled...

Wow Perfect. Dam you make it hard to argue..Ok and I hate being a K447 fanboy But Damit..
The ski and trailer act as 1
Perfect.
dont think I have even seen it done Perfect like that,except on a 4...

http://greenhulk.net/forums/attachment.php?attachmentid=467005&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=467006&stc=1
75% of the time the back straps will work,
but watching my...

I take heat for this all the time.... but
Back straps are worthless when you really need them.
1 strap from trailer over craft back to trailer, is the best way....

TigerShark Pwc

power comes from ecu and there should be a fuse in the wiring harness under the intake manifold with a 2 or 3 amp fuse.

big time 10-12 mph
start motor , trim up , leave running , adjust rod in rear to move nozzle higher..
But with any weight - rider or passenger- you can get stuck with a bounce..
I weigh as much as...

I think it is a 2 degree wedge ,, https://www.4-tecperformance.com/index.php?main_page=product_info&cPath=350_94_384&products_id=6277&zenid=lltq2nmv4o86vcfnprosfp2hd2
In the heat now, im down to...

Wow ,Sucks, Will be very missed..
R.I.P.
Till We Ride Again
http://greenhulk.net/forums/showthread.php?t=77836&p=1373839&viewfull=1#post1373839

battery vent tube

got a call to check on a VX that would not start..
Crank ski and by the sound I can tell there is no compression.. Pull a comp test 0-0-0 psi.. Ruh-roh...
So apparently somebody broke a spark plug...

Love my Vx HO 1.8L
I do work on about 20 rental vx's with the Tr1's and half of them have done 1000 hours in 10 months, with no (big) problems ..
if you dont change oil enough it will kill itself...

have you checked the air intake hoses are not stuck to the floor???
have you run with seats off?
what rpm's are you turning ??
probably need an aftermarket tach - stock display is shit when...

https://www.youtube.com/watch?v=Mh6SCYxAdSI&feature=emb_logo