Search

2021. Talked to my dealer and Yamaha hasnt done anything about it yet as far as he knows. When you access the plate on the yamaha parts page you can see the part number but cannot order the part. ...

I agree with going by rotation after seated by hand but one important note is there's a big difference between brand new plugs with un-crashed washer and one that has been previously installed and...

I agree, because Yamaha never advertised that the "transom plate" was 160mm. That is something that I learned while at the press introduction when I rode the ski and I passed on to the forum members...

Take ski to your dealer, they will verify the part number and send the info to Yamaha they will make it right. I contacted Yamaha through the yes warranty department the person I spoke to was very...

If the 2021 part numbers are not yet available on the OEM part finder link toward the top of the page then I would roll with the casting number that shhr provided in post #24 above. Call your dealer...

I agree, I am going to start trying to contact Yamaha directly to see what they have to say.
Gerry, is this something you can also bring to the attention of any Yamaha folks?

Can someone...

Guys, speaking as a manufacturing engineer this is a big deal. How this slipped thru the quality control process on their assembly line is a big deal. I don't work for Yamaha, but knowing what I know...

Ok here is what I have. I have 2 GP1800 one with the date of 9/11 one with a date of 10/13. The 10/13 has the correct transom plate the 9/11 boat has the old style. I have also confirmed 4 other...

Those tears are pretty substantial. I’d fill them in... there’s ways to do it by gluing foam into the cracks, then glue the vinyl back down.

There’s also videos by The Jetski Store.

Before my first Yamaha hull repair I purchased paint kits from from ColorRite (the Yamaha 'official' repair paint source). We have one red and one blue GP1800. I ordered color correct base coat for...

So finally after all go it working, and wanted to give an update in case someone in the future finds themselves on this position.

Also wanted to give thanks to all who chimed in with a posible...

I used an independent eye practitioner who sent the frames away with the lens order.

If I was to do it again I would probably let SeaSpec do the prescription lens directly.

The tricky part...

http://greenhulk.net/forums/showthread.php?t=76954&page=7&highlight=bomb+proof

Post Number 64. I built one of these without the wheels. It has been outside on the edge of the woods in my yard...

I think you pretty much answered your own questions.A 16 degree pitch with a small nozzle is not moving as much water volume and can feel lazy on the bottom end.If you add a tail cone on that setup...

That was it the battery went dead and kicked on the security system. Thank you very much for your help

That sounds like the grate is pushing in more water than the slowing down pump can process creating mini stuffs.

From a satellite view it may be deceiving, but the canals are pretty wide and clean. Most vegetation (if any) is usually along the shoreline with plenty of space to ride debris free.

There are...

Many of these things have NEVER been greased since new. On those, the grease has probably hardened inside the hose. Best thing to do if you're not sure if it's been serviced is to remove the hose...

Casting resin can be used to fill the hollow voids in the aluminum castings but it would not be used to seal the sections of the jet pump to each other.

I have used 3M 4200 Fast Cure sealant...

I wouldn’t put a SBT engine on my lawn mower. I used them once and never again.

I had my 2019 FXSVHO re-flashed last week and went on a short ride today. I started with a full tank, using the slow fill method to make sure the tank was actually full. The fuel gauge was reading...

OEM is handling what it's designed to do. If aftermarket can't keep up, you may need to ask what you're really trying to accomplish. Anyone running over 94MPH is not recreationally riding their ski,...

i dunno maybe its just me...but i dont see how you can blame yamaha for you running a machine at over 90 mph and 9000rpm.....Clearly they didnt intend people to try and make it a space ship.

this...

You see those rust spots in the ring? The aluminum corrodes and pushes the ring into the impeller. Time for a new housing.

On my own watercraft I keep the battery fully connected as per normal. I use the installed pigtail charging lead as needed during the season without any concern for the PWC electronics.

My view is...