Search

Type: Posts; User: Ziggy

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    416

    WTB - Parts Bump

    Bump
  2. Replies
    5
    Views
    416

    WTB - Parts 2008 RXP-X drive shaft

    I need a good clean 2008 RXP-X drive shaft. Fresh water preferred but not critical.
    Thanks!
  3. Replies
    17
    Views
    3,228

    I wish I had something installed in the ski!...

    I wish I had something installed in the ski! :facepalm:
  4. Replies
    17
    Views
    3,228

    PM sent - thanks!

    PM sent - thanks!
  5. Replies
    17
    Views
    3,228

    This is the shaft I need to cut: ...

    This is the shaft I need to cut:

    http://www.greenhulk.net/forums/attachment.php?attachmentid=433770&stc=1
  6. Replies
    17
    Views
    3,228

    Anybody know how long these are? I kinda wanted...

    Anybody know how long these are? I kinda wanted to remain consistent with the shafts already out there so I wasn't reinventing the wheel, so to speak. If it helps, I'm using the '02+ splined section...
  7. Replies
    17
    Views
    3,228

    Conversion shaft info - length?

    If anyone has a GPRXP mid shaft handy, could you tell me the overall length (RXP(X) shaft section + Yamaha splined section). Trying to get one made, but I removed the entire mid-wall and have no...
  8. Replies
    27
    Views
    5,047

    Very nice! What material did you use?

    Very nice! What material did you use?
  9. Replies
    6
    Views
    435

    WTB - Parts Thanks for the info. I'm pretty ignorant about...

    Thanks for the info. I'm pretty ignorant about Yamahas.
  10. Replies
    6
    Views
    435

    WTB - Parts Toxicgun, if my measurements of the inside of the...

    Toxicgun, if my measurements of the inside of the midshaft are to be trusted, it looks like the drive shaft OD should be 20mm with 18 splines.
  11. Replies
    6
    Views
    435

    WTB - Parts It could, I honestly don't know for sure. Anyone...

    It could, I honestly don't know for sure. Anyone know the answer to this question?
  12. Replies
    6
    Views
    435

    WTB - Parts Still looking....

    Still looking....
  13. Replies
    6
    Views
    435

    WTB - Parts GP1300R drive shaft

    I need a used (any condition) drive shaft from a GP1300R. All I need is the splined end that goes into the midshaft and about 8" after it to make a hold-back tool. I can't seem to find a...
  14. Replies
    27
    Views
    5,047

    I wonder if he is still doing this work. I've...

    I wonder if he is still doing this work. I've never received a response from him.
  15. I've been trying to get ahold of him too. Trying...

    I've been trying to get ahold of him too. Trying to get a shaft made after he posted his desire to build shafts for forum members, but he is not to be found. You never know what is going on in...
  16. Replies
    4
    Views
    400

    WTB Yeah, pretty much.

    Yeah, pretty much.
  17. Replies
    4
    Views
    400

    WTB I appreciate the referral, but that is too...

    I appreciate the referral, but that is too stripped & rough. Thanks anyway.
  18. Replies
    4
    Views
    400

    WTB Looking for 2008 RXPX w/o motor

    Interested in buying a 2008 RXPX with no motor, blown, ingested, otherwise non-functioning motor. Need the hull to be in good or better condition.
    Thanks!
  19. Replies
    27
    Views
    5,047

    PM sent, are you still doing drive shafts?

    PM sent, are you still doing drive shafts?
  20. Thread: Conversion shaft

    by Ziggy
    Replies
    1
    Views
    340

    WTB Conversion shaft

    Need a conversion shaft for the Sea-Doo to GPR HO setup. I want to use the HO GPR parts(shaft, pump, etc.) to complete my build. If anyone is still making these, I'd prefer to buy new. Thanks!
  21. Thanks! Is the cavitation to be expected with a...

    Thanks! Is the cavitation to be expected with a 255 HP setup or is it a factor of the higher HP you ran?
  22. Thank you for all of that! Really helps. Now I...

    Thank you for all of that! Really helps. Now I have some solid info to go hunting for parts. Oh, and a machinist. :)
  23. Would this be good? ...

    Would this be good?

    https://www.ebay.com/itm/202200416591?ssPageName=STRK%3AMEBIDX%3AIT&fromMakeTrack=true
    http://www.greenhulk.net/forums/attachment.php?attachmentid=428705&stc=1
  24. I like this idea the best. I want to get this...

    I like this idea the best. I want to get this thing going by May and I still need to paint it. I'll contact [/COLOR]Kmorningstar_rxp and see if he has a source for the conversion shaft with the SHO...
  25. With the HO pump can you use the original transom...

    With the HO pump can you use the original transom plate? What years of the HO pump will work? What length driveshaft?
    Thanks for the input!
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4