Search

Type: Posts; User: ripcuda

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    4
    Views
    116

    That's quite impressive that you tore down the...

    That's quite impressive that you tore down the whole front of the engine while still in the hull!

    With the intermediate gear in your pic... did you rotate the engine to turn over that gear and see...
  2. Replies
    4
    Views
    116

    So... when it says overtemp... and you pull the...

    So... when it says overtemp... and you pull the seat up... does it "feel" like the engine is getting excessively hot?

    So you have no coolant flow into the reservoir bottle? Only at idle or when...
  3. Replies
    7
    Views
    314

    Be sure the oil tank you find on ebay has the...

    Be sure the oil tank you find on ebay has the water jacket (water flowing through it). Hydrospace (HS4) oil tanks do not have a water jacket. Ensure it has all the correct ports. See the pictures...
  4. Replies
    7
    Views
    314

    Welcome. 1. I'm guessing you've ruled out...

    Welcome.
    1. I'm guessing you've ruled out leaking coolant into the hull. Often it will only leak under full pressure (top speed). Other ways to loose coolant could be a blown headgasket. You need...
  5. Replies
    2
    Views
    142

    Welcome to GH! Yes, agree with Hiperco... that...

    Welcome to GH!
    Yes, agree with Hiperco... that is the battery vent for use when you have a lead acid battery. If you run the better AGM sealed batteries, you won't use it... just tuck it out of the...
  6. The driveshaft seemed factory aligned. There...

    The driveshaft seemed factory aligned. There were no noticeable vibrations. And usually when a driveshaft is out of alignment... it wears out the PTO coupler or impeller threads. This ski has not...
  7. Rebuilt jet pump lasts an hour - what did I miss?

    Hi Gang,
    A friend recently picked up a nice '96 GTX. It has no thrust and bad jet noises so he had me take a look. I pulled the pump and it was a mess. The needle bearings were destroyed. The...
  8. Replies
    11
    Views
    285

    Since you have a complete donor ski... it should...

    Since you have a complete donor ski... it should be possible. Everything is going to need to swap into the SL... and that's a tight fit!

    Tricky parts will be engine mounts... as I'm not sure the...
  9. Agreed. Get some new intake gaskets. You've...

    Agreed. Get some new intake gaskets. You've come this far. I'd also look to replace the crank end seals. Those old ones can leak air into the engine leaning it out. When done, pressure test the...
  10. Replies
    3
    Views
    139

    The hardpipe from intercooler to throttlebody is...

    The hardpipe from intercooler to throttlebody is different on 150... has the BOV on it. While this isn't absolutely necessary... it is a recommended part. The BOV helps save turbo from flutter.
    ...
  11. This had happened to my first 750 also. I pulled...

    This had happened to my first 750 also. I pulled the engine to remove the flywheel to remove and replace the magneto with a good used one. Then ran the wires back to the ebox. Some say you can...
  12. Go here: ...

    Go here: http://polarispwcknowledge.shorturl.com/polaris-fuji-engine
    read and learn all the info contained in the various forum threads listed there by topic.
    There are links there explaining the...
  13. You definitely sound like you are having a lean...

    You definitely sound like you are having a lean condition. Did you remove the Autocock? Did you upgrade your fuel pump? Did you test your fuel lines to ensure you weren't sucking air (like say...
  14. Welcome to GH! That's an impressive recovery...

    Welcome to GH!

    That's an impressive recovery story. Glad it worked out.

    Cheers!
  15. Sticky: I've bought a few of the aftermarket Seadoo fuel...

    I've bought a few of the aftermarket Seadoo fuel selector valves off fleabay. They do work... and are a direct replacement... but they are no-where near the quality as the OEM one (go figure).
    In...
  16. Replies
    3
    Views
    83

    Concur. You do not need the more expensive fuel...

    Concur. You do not need the more expensive fuel injection hose... just the regular fuel hose... 1/4"... low pressure carb stuff. My auto store carries Gates brand fuel hose.

    Cheers!
  17. Wow! Very clean '95 SLT 750. I love'em... got...

    Wow! Very clean '95 SLT 750. I love'em... got 3.

    Cheers!
  18. Replies
    3
    Views
    123

    Welcome to GH! Great first ski! Was mine also....

    Welcome to GH!
    Great first ski! Was mine also.

    I can't stress enough the need for you to fix/update it before you use it. Fastest way to kill the engine is to try and get an old, neglected...
  19. Replies
    7
    Views
    125

    And by pump bolts... he's referring to the 4 LONG...

    And by pump bolts... he's referring to the 4 LONG bolts that fasten the entire jetpump assembly to the hull... not the nuts on the inside of the hull that fasten the pump base to the hull (don't...
  20. Thread: Polaris??

    by ripcuda
    Replies
    8
    Views
    299

    Super fun solo ski. While a 2-seater... it's...

    Super fun solo ski. While a 2-seater... it's very tipsy with 2 on it. I've watched many a folks roll it trying (good fun)! I prefer the SLT 3-seater models which are a little less tossable (can...
  21. Thread: Polaris??

    by ripcuda
    Replies
    8
    Views
    299

    '96 Polaris SL780 stock, it looked like this...

    '96 Polaris SL780

    stock, it looked like this
    http://greenhulk.net/forums/attachment.php?attachmentid=451078&stc=1
  22. Thread: Polaris??

    by ripcuda
    Replies
    8
    Views
    299

    Is this your jetski? ...

    Is this your jetski?

    https://www.youtube.com/watch?v=q1P-guyBZEA
  23. Thread: Polaris??

    by ripcuda
    Replies
    8
    Views
    299

    Welcome to GH. Post up a pic... that will...

    Welcome to GH.

    Post up a pic... that will help.

    Last 2 digits of HIN are the year. Blue engines are 650, 750 or 780. 650 and 750 say "650" or "750" on the rail that runs across the top of the...
  24. Replies
    15
    Views
    455

    The MSX coolant elbow is pressed in. The FST...

    The MSX coolant elbow is pressed in. The FST elbow is bolted in sealed with an o-ring. You might be able to machine the FST block to accept the MSX coolant elbow... or press fit it in somehow... or...
  25. Replies
    15
    Views
    455

    Howdy. Spencer's build (link above) is the only...

    Howdy.
    Spencer's build (link above) is the only one I know of that actually did it. I too have a nice FST block that I plan to use, if I ever get around to it.

    You will need the special...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4