Search

Type: Posts; User: Dryburgh27

Search: Search took 0.00 seconds.

  1. Replies
    11
    Views
    1,272

    View Post

    Iím running the 8650 setup on my PX with the VT11ís, canít recall what it was doing before I retarded the cam but Iím getting a solid 82 flicking to 83 occasionally at 8500Rpm (dash mph) stock...
  2. Jesus could you clarify the fuel system setups...

    Jesus could you clarify the fuel system setups please, I already have the VT11 injectors on my ski as part of the stage 2+ setup so I’m assuming if I added the cam with the correct map I shouldn’t...
  3. Thanks for the feedback guys! sounds like the cam...

    Thanks for the feedback guys! sounds like the cam will be a worthwhile addition to the ski :)
  4. That would be ideal if picked up 2-3 up top, that...

    That would be ideal if picked up 2-3 up top, that alone would be worth it, have you found the cams make a noticeable improvement in acceleration aswell? Heard a few people say it really wakes up the...
  5. RXP 300 - Adding Cam to Stage 2 Plus setup? (Stock Charger)

    Hi all,

    I had been considering the ET135 wheel for my 300, however after hearing about some people having issues with vibrations or compressor surge on partial throttle I'd much rather stick with...
  6. Replies
    0
    Views
    132

    OEM 300 Exhaust outlet size?

    Quick question as I don't have my ski around at the moment to measure, I know Rivas rear (through hull) exhaust for the 300PX comes with a 3'' outlet but anyone know if the OEM outlet on the 300PX is...
  7. Replies
    0
    Views
    210

    T3 Hull Exhaust Outlet Position?

    Hi all, just have some questions regarding fitting a rear exit exhaust on the T3 hull specifically a RXP 300.

    Iíve seen people mount the outlet in different positions mainly the way Riva shows...
  8. Replies
    7
    Views
    1,202

    Ski only has about 13hrs on it so bearings wont...

    Ski only has about 13hrs on it so bearings wont be an issue. I just wondered if I need to replace the wheel retaining nut or the 2 nuts to set the clutch slip? Or can i just re-use the existing nuts...
  9. Replies
    7
    Views
    1,202

    Few Q's about the ET-135 Wheel...

    Hi folks, currently running Riva Stage 2+ and thinking about trying an ET135 wheel in my RXP 300, just got a few questions regarding installing it.

    From what I've read it seems most people just...
  10. Replies
    6
    Views
    1,027

    CM Tech - Acrylic safe shampoo/polish?

    Hi folks, just wondering what people are using to clean and polish there CM Tech skis ?

    Iíve tried searching for acrylic safe products but not having much luck finding anything. If anyone has any...
  11. Replies
    3
    Views
    1,284

    100% right, just had confirmation from RIVA no...

    100% right, just had confirmation from RIVA no need to pull fuses on 18-19 skis.

    Thanks
  12. Replies
    11
    Views
    1,939

    Fault code disappeared but I had the dealer do a...

    Fault code disappeared but I had the dealer do a diagnostic anyway, everything checked out 100% OK.

    Later discovered the fuses hadn't been inserted correctly at the factory, there were all loose...
  13. Replies
    3
    Views
    1,284

    2019 RXP Tune Upload?

    About to flash my 2019 RXP 300 with a Riva stage 2 tune.

    Instructions I have seen say to remove the IBR fuses a 5 amp and 30 amp.

    My 19 RXP only seems to have a single 30A for the IBR system,...
  14. Replies
    11
    Views
    1,939

    IBR fault code

    Picked up a new RXP 300 yesterday so iíve been out breaking it in this weekend and noticed it is showing an IBR Module Error Code C2114

    Will be getting in touch with the dealer tomorrow but just...
  15. Replies
    2
    Views
    325

    Perfect, thanks!

    Perfect, thanks!
  16. Replies
    2
    Views
    325

    300 Breather hose I.D

    Hi all new to the forum :)

    Does anyone happen to know the internal diameter of the breather hose that runs from the engine to either the intake or a catch can?

    Cant seem to find the ID...
Results 1 to 16 of 16