Search

Type: Posts; User: Myself

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    11
    Views
    485

    I don't trust aftermarket stators as far as I can...

    I don't trust aftermarket stators as far as I can throw them. I have a 717 GTi here right now. Let me check the cranking voltage and see what it is.
  2. Thread: Hull Repair

    by Myself
    Replies
    7
    Views
    359

    Here's what I use. ...

    Here's what I use.
    ...
  3. Thread: Hull Repair

    by Myself
    Replies
    7
    Views
    359

    First, jack the side up and get the ski leaned...

    First, jack the side up and get the ski leaned over some. You'll need to degrease and wash that oily area.......many times. When it's pretty clean looking, use non flammable brake cleaner and a heat...
  4. Replies
    11
    Views
    485

    That would be my guess......I'd sure try a...

    That would be my guess......I'd sure try a different one.
  5. Replies
    11
    Views
    485

    Ok, make sure your meter is reading...

    Ok, make sure your meter is reading properly.....stick the leads in an outlet and check for 120vac.

    My notes say yellow to yellow 6vac while cranking.
    Blk to blk/red 20vac while cranking.
  6. Replies
    11
    Views
    485

    Stator ohms can be well within spec but have low...

    Stator ohms can be well within spec but have low output voltage. Give me a minute.......
  7. Replies
    11
    Views
    485

    Let me check my notes tomorrow on those cranking...

    Let me check my notes tomorrow on those cranking voltages.
  8. Replies
    26
    Views
    1,655

    Not to mention, the starter drive is clutched and...

    Not to mention, the starter drive is clutched and would just freewheel in the wrong direction......wouldn't even crank the engine over.

    Maybe just coincedence and the midshaft splines OR impeller...
  9. Replies
    14
    Views
    325

    I'd guess for 1000hp you need to start with a...

    I'd guess for 1000hp you need to start with a plain Yamaha with 1.8l. Then spend 30k or more on all the custom made parts to get you there.
  10. Replies
    29
    Views
    668

    Well, after a few minutes of research it appears...

    Well, after a few minutes of research it appears the constellation of which 'Polaris" is a part of is rooted in Greek astrology. That means, according to proper grammer, that the plural shall be...
  11. Replies
    29
    Views
    668

    Are you guys sure the plural for of Polaris is...

    Are you guys sure the plural for of Polaris is not 'Polarii".....???
  12. Replies
    29
    Views
    668

    If you're talking about the points on the lift...

    If you're talking about the points on the lift bars sort of laying over and pushing INTO the hull.......all the lifts do that with some hulls. Just fold a towel in half and place under the metal so...
  13. Thread: Stock exhaust

    by Myself
    Replies
    3
    Views
    247

    You will need ALL of the exhaust. From the...

    You will need ALL of the exhaust. From the manifold all the way back. I also have a whole set here.
  14. Replies
    11
    Views
    485

    What is your battery voltage while cranking?

    What is your battery voltage while cranking?
  15. Good luck!! Hard to find a real machinist at all...

    Good luck!! Hard to find a real machinist at all these days. Just warm bodies standing in front of equipment and pushing a button now and then. I paid to have a local guy build a thick steel plate...
  16. Replies
    4
    Views
    254

    Yes, you can just backprobe the wiring connector....

    Yes, you can just backprobe the wiring connector. I do it all the time.
  17. Replies
    3
    Views
    371

    Well.......I think I would contact Westside...

    Well.......I think I would contact Westside Powersports and buy a good used RAVE set. If you try a completely different set and get the same results then it's NOT the RAVEs. If it fixes the issue...
  18. OK, if that bolt was accessible from outside then...

    OK, if that bolt was accessible from outside then maybe it was a press fit. You can't find it in the OEM drawings cause it's not an OEM part. It was added to help carry the load of the flywheel at...
  19. Replies
    6
    Views
    370

    Several companies can take any ECU and flash it...

    Several companies can take any ECU and flash it to work with any year machine. Try contacting Torx Racing.
  20. Check the big square MPEM connectors for moisture...

    Check the big square MPEM connectors for moisture or corrosion. I've seen a couple do that when they had water drops in them. Otherwise......likely the ECU.
  21. That would not have been a tight pressed fit....

    That would not have been a tight pressed fit. Likely designed to come apart exactly as it did. Upon reassembly I think I would add a few dabs of Threebond or RTV to the race just to keep it from...
  22. Replies
    6
    Views
    370

    In my dealings, I have found that the software...

    In my dealings, I have found that the software CAN communicate with the ECU or MPEM without the correct key. So if the BUDS can't communicate then I suspect a bad ECU, which happens to be pretty...
  23. Replies
    0
    Views
    281

    FS Tigershark 1100 project skis

    I've got a TSR1100 and a TSL1100Li and 2 Monte Carlo 900's. Plan was to use the 1100 parts to fix the TSR. I've already done the research and the cylinders are the same, and the crank is the same...
  24. FS Winter projects. Let me put you in the Polaris business, LOL!

    I've got a bunch of Polaris skis sitting around. How about somebody make me an offer and come get ALL of them!! I have good papers and enough parts to make 4 running skis! SO many projects so...
  25. Replies
    6
    Views
    467

    I think if it were mine......and I'm stating this...

    I think if it were mine......and I'm stating this over the fact that in the last 2 seasons I've had 3 dead low hour 310's picked up here by the insurance companies for failed engines....I would go...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4