Search

Type: Posts; User: tiderider

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Hi, yes your right about the large gaps. I listed...

    Hi, yes your right about the large gaps. I listed the wrong information from the spec sheet... I listed the Groove width for each ring, not the gap. I guess my machinist did his magic for the ring...
  2. My other engine with et137+4mm got the .0033...

    My other engine with et137+4mm got the .0033 treatment using 100.5 CP 8.4:1 and coated skirts.. Only 1.5 hours on it though... Did a couple 8200 rpm WOTs with no issues..
    CP Piston rings were set...
  3. Hey Thank you! How much psi are you doing at WOT...

    Hey Thank you!
    How much psi are you doing at WOT with your setup?
  4. Wiseco piston to wall clearances for 40038M10050 100.50mm Pistons , 4 tec

    Hi, can anyone confirm piston to wall clearances for the wiseco 40038M10050 pistons for a maximum of 13-15 psi at wot? Wiseco USA says .0020 - .0025 and Wiseco Canada says, on the box states .0019
  5. 215-260hp upgrades to 300 supercharger results or outcome?! Which Year and ECU if so?

    Hi, I just purchased a used stator/timing cover with an excellent oil pump present in it. After looking at the images closely... It appears that its the newer covers with that special oil return...
  6. Replies
    1
    Views
    105

    WTB 420834874 Starter Double Gear

    Can't help notice that many are upgrading their old style superchargers for the new 300s. Just wondering if anyone wants to sell their OEM flywheel? It has to be from a non failed engine in great...
  7. Its just a question out of curiosity! Yes a new...

    Its just a question out of curiosity! Yes a new chain is going in.. lol
  8. Just curious, a new timing chain is going in!!...

    Just curious, a new timing chain is going in!! Thank you!
  9. Used and Unknown hours on IWIS timing chain

    Does anyone know if there is a clear way to know if a timing chain should be replaced or reused if hours are not known? The service manual displays, bending the chain side to side as a visual.. But...
  10. Thank you for all your efforts and advice!

    Thank you for all your efforts and advice!
  11. Thank you so much! Your such a kind person!

    Thank you so much! Your such a kind person!
  12. Hi, do you know if the spring washers are sized...

    Hi, do you know if the spring washers are sized and exactly as the ones on the supercharger shaft? Thank you!
  13. Replies
    4
    Views
    857

    Anyone have exact dimensions for the washers?...

    Anyone have exact dimensions for the washers? Thrust washer and spring washers?
    Are the spring washers the same as the ones used in the superchargers? Same washers, different item numbers?
    Thank...
  14. Starter Bendix 1 x Thrust washer and 2 x spring washer dimensions

    Hi, would anyone have a set of washers for the starter bendix? This would be for the 4 tec engines. I am looking for dimensions if possible.
    1x Thrust washer's inner, outer dimensions and thickness?...
  15. Replies
    47
    Views
    1,933

    Edelbrock has the rebuild kits for the Riva...

    Edelbrock has the rebuild kits for the Riva branded RRFPR.
  16. Replies
    50
    Views
    1,984

    I would get rid of it instead, take your small...

    I would get rid of it instead, take your small purchase loss and run..
  17. Replies
    50
    Views
    1,984

    Ouch!!! SBT! Don't use their connecting rod...

    Ouch!!! SBT! Don't use their connecting rod bolts. Bad experience in the past, i ended up sending them back to SBT, poor quality, it was like the bolt threads were cross threaded from factory..
  18. Replies
    5
    Views
    189

    Yes, it would easier and cleaner to pull the...

    Yes, it would easier and cleaner to pull the engine.
  19. Replies
    15
    Views
    638

    The head does not have to come off in order to...

    The head does not have to come off in order to replace the crankshaft. The rocker arm does in order to simplify timing, etc.
  20. A Good Seadoo 4 tec machine shop in Washington?

    Hi, does anyone know of a good machine shop in Washington state for the seadoo 4 tecs? Looking to find a better option than sending it off to another state every time something needs done.. Looks...
  21. Replies
    15
    Views
    638

    Main or lower 8 x bolts do not need replacing,...

    Main or lower 8 x bolts do not need replacing, they can be reused.
    I just installed a complete WSM set of bearings. Crankshaft main bearings, counter balance bearings, connecting rod bearings and...
  22. Replies
    50
    Views
    1,984

    Make sure all the fuses are good and that none...

    Make sure all the fuses are good and that none are missing..
  23. Replies
    4
    Views
    367

    Find a used one or bite the bullet for a new one....

    Find a used one or bite the bullet for a new one. Dealer will marry it to the cluster in no time.
  24. Replies
    50
    Views
    1,984

    The junk yard would be a good place to take it..

    The junk yard would be a good place to take it..
  25. It was an online seller who had 1 last set in...

    It was an online seller who had 1 last set in stock.. Good timing!! $60 is connecting rod bolts alone if I would have replaced only 1 OEM con rod.. Molnar con rods come with ARP2000 reusable bolts....
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4