Search

Type: Posts; User: Myself

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    20
    Views
    518

    Just added the inline checks and did nothing...

    Just added the inline checks and did nothing else. The overpressure bubbling the line was because the carb check valve was jammed up with crud. Probably contributed to killing the original top end.
  2. Replies
    20
    Views
    518

    I have placed the Yamaha valves inline a couple...

    I have placed the Yamaha valves inline a couple times.....no issues. In fact, I have a pic here somewhere of a marble sized bubble in an oil line. The check valve was jammed up and the oil pump just...
  3. Replies
    4
    Views
    286

    WTB - Parts Some knucklehead snapped one off. I was able to...

    Some knucklehead snapped one off. I was able to extract it and save the threads so just need to put one back in.
  4. Replies
    4
    Views
    232

    Oh no!!

    Oh no!!
  5. Replies
    4
    Views
    232

    Would love to see some engine pics of that Ultra....

    Would love to see some engine pics of that Ultra. I'll bet at 180psi that thing rips!!
  6. Replies
    2
    Views
    178

    If it's no longer available from Yamaha you'll...

    If it's no longer available from Yamaha you'll need to have one made. Any graphics shop should be able to use a high quality pic of the opposite side, flip it in the software, and print one out for...
  7. Where there's a will..........there's a way. I...

    Where there's a will..........there's a way. I have no doubt your next one will be even better. I shipped a bunch of oddball parts to Russia once. The freight was very expensive. My buyer told me...
  8. Replies
    4
    Views
    286

    WTB - Parts This one is a '99. I only NEED one but would take...

    This one is a '99. I only NEED one but would take 2 so I have one around next time.
  9. Replies
    7
    Views
    420

    A 4 stroke crankcase isn't really completely...

    A 4 stroke crankcase isn't really completely sealed and holding pressure like a 2 stroke case. Everywhere oil goes would need blocked off...valve cover, tip over switch, dipstick tube, output shaft,...
  10. Replies
    3
    Views
    87

    Most likely places on on old 650 will be the mid...

    Most likely places on on old 650 will be the mid shaft seals, and the old fiberglass waterbox.
  11. I had a customer with an LS2000 that ran great...

    I had a customer with an LS2000 that ran great after I did pumps and carb mods.
    I have another customer with a twin engine Exciter that I need to tune in this spring.
    They really are strong when...
  12. Replies
    8
    Views
    532

    Anything boosted will NOT run right with a non...

    Anything boosted will NOT run right with a non boost ecu. The computer cannot compensate. Maybe he's done spending money cause he bought the wrong ecu.......you'll never get the truth about that lol!
  13. Replies
    8
    Views
    418

    When I've done it they were so close that just a...

    When I've done it they were so close that just a wee bit with a flat bastard file was all that was needed. You gotta clamp it after the sleeve goes in though. They do tend to try and rise up.
  14. Replies
    20
    Views
    672

    Yes! That is a known issue and common failure...

    Yes! That is a known issue and common failure mode. Perform the balanced return mod to keep that from happening.
  15. Replies
    20
    Views
    672

    Hard to see the check discs with the glare but if...

    Hard to see the check discs with the glare but if they are still flat with no little creases anywhere they're good. Sounds likely you were sucking air around the base gasket.
  16. Replies
    8
    Views
    418

    Yes. All non pv 1200's are the same. Suv uses the...

    Yes. All non pv 1200's are the same. Suv uses the 65u just like 97-99 GP1200.
  17. Replies
    20
    Views
    672

    The pump side, 2 little round discs with a little...

    The pump side, 2 little round discs with a little rubber center.
  18. Replies
    20
    Views
    672

    Yes, an air leak at the carb base will cause a...

    Yes, an air leak at the carb base will cause a lean condition. Pop the cast rectangular cover on that center carb. Let's see the round check discs.
  19. Replies
    9
    Views
    345

    And here is the finished guage reinstalled with a...

    And here is the finished guage reinstalled with a new face decal. I had trouble getting a good pic cause of glare and reflection but it's now plainly legible again. =D>
  20. Replies
    9
    Views
    345

    Next everything got put back together with a...

    Next everything got put back together with a little bit of marine epoxy I had, then lightly clamped for 48 hours.
  21. Replies
    9
    Views
    345

    I used a very small flat blade screwdriver with...

    I used a very small flat blade screwdriver with tape over the tip to carefully pry the lcd out of the housing. It has to tilt a bit, the top (opposite the white strip) has to come up a bit first. In...
  22. Replies
    9
    Views
    345

    And when the board is removed it looks like...

    And when the board is removed it looks like this!! The gold rectangle is the gauge background. You could cut a piece of any color graphic vinyl and change this if you want to customize. The white...
  23. Replies
    9
    Views
    345

    When you get it open there are 5 small phillips...

    When you get it open there are 5 small phillips head screws that need removed.
  24. Replies
    9
    Views
    345

    I used a dremel with a cutoff wheel to cut around...

    I used a dremel with a cutoff wheel to cut around the edge just behind the face.
  25. Replies
    9
    Views
    345

    Ultra 150 & STXr guage repair

    I've done several Seadoo gauges and thought I'd give a Kawi gauge a try. I verified this guage was still working with a strong flashlight and my polarized sunglasses. I could just make out most of...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4