Search

Page 1 of 13 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    11
    Views
    354

    I think I do want the replacement as it is under...

    I think I do want the replacement as it is under warranty, then I will order a Fizzle and put the stock 300 IC on my wifes 230 as it is better than the one on the 230.

    But they need to fix the...
  2. Replies
    10
    Views
    456

    If you are cruising and under 6000rpm,...

    If you are cruising and under 6000rpm, essentially out of boost. Your fuel economy will be very similar, n/a vs s/c. However if you pin it to win it, their is a drastic difference in fuel economy. ...
  3. No doubt man, I feel like I could do it all over...

    No doubt man, I feel like I could do it all over again in half the time now knowing what I know. I’m going to have Steve take a look at the driveshaft and see what he thinks. The splines all looked...
  4. Replies
    3
    Views
    251

    Don't use any nose cone at all. They are...

    Don't use any nose cone at all. They are problematic, walk up the shaft and cause cavitation. Believe it or not your ski is faster without an impeller nose cone.
  5. Replies
    12
    Views
    1,478

    Replace them with AWAB and then considered it...

    Replace them with AWAB and then considered it bullet proof.. http://www.awabllc.com/
  6. Replies
    43
    Views
    2,117

    Hey listen, the point of this forum is to ask...

    Hey listen, the point of this forum is to ask questions. We are not all experts, I’m no expert by all means but I’m very handy with tools and with good knowledge and good advise I try al take the...
  7. Replies
    43
    Views
    2,117

    Come on NC, you know that I love oil threads!...

    Come on NC, you know that I love oil threads!
    There really have been too many Doos that have sunk the past two years due to factory alignment issues. People do need to pay more attention in the...
  8. Replies
    43
    Views
    2,117

    There is no need to redesign it, a properly...

    There is no need to redesign it, a properly installed and aligned seal will last over 200 hrs and many years.
    I replaced mine at 150 hrs and 14 years and it was not leaking and only worn down 1/8 of...
  9. Replies
    15
    Views
    939

    Boost gauge (while running @ speed) would tell...

    Boost gauge (while running @ speed) would tell you a lot.
  10. 103 mm bore? Stock head gaskets may not be large...

    103 mm bore? Stock head gaskets may not be large enough...

    http://www.easyrider.store/product/rs-3052-gasket-cylinder-head-1730cc-4-blades-103mm/
    ...
  11. Maybe not the message you want to hear but if you...

    Maybe not the message you want to hear but if you like riding with the family like you described you bought the wrong model ski!

    I sometimes take one of the little ones with me on the RXP but if I...
  12. Replies
    12
    Views
    1,881

    I agree with Jerry on this matter. That said and...

    I agree with Jerry on this matter. That said and knowing what I know now, I recommend that if you are thinking of spinning your engine beyond 8800 rpm and especially with big boost, do it right the...
  13. Replies
    12
    Views
    1,881

    You absolutely will NOT lose RPM with the spring...

    You absolutely will NOT lose RPM with the spring and retainer kit... that's yet another internet myth
  14. Replies
    35
    Views
    2,018

    Do yourself a fAvour and make sure you get...

    Do yourself a fAvour and make sure you get submersible fuel line or you will end up having a bad day again.
  15. Replies
    106
    Views
    12,297

    His ski!

    His ski!
  16. Replies
    106
    Views
    12,297

    The prop Waterforfire posted a couple pages...

    The prop Waterforfire posted a couple pages before in this post has been on my 2018 RXTX since new. It was Waterforfire's idea to do a prop--15-22--and send it to Dave to fit by boat. The...
  17. Replies
    106
    Views
    12,297

    They do voodoo magic, my glen prop looks like a...

    They do voodoo magic, my glen prop looks like a work of art. Pitch blocked/trued/balanced/race finished/diameter milled to perfection. Hard to do with average garage tools.
  18. Replies
    106
    Views
    12,297

    I found my old turbo props when I was packing. ...

    I found my old turbo props when I was packing. Wild times and I miss it
  19. Pump/engine alignment could be causing your...

    Pump/engine alignment could be causing your problems.
  20. Good point! And adding my 2 cents, send any...

    Good point! And adding my 2 cents, send any Solas impeller directly to Skat to have the pitch checked/equalized. I have never seen a Solas impeller where all the blades were the same pitch, length,...
  21. Replies
    5
    Views
    528

    sinkage recovery typical includes disconnecting...

    sinkage recovery typical includes disconnecting each reasonably accessible electrical joint, blow drying with compressed air and regreasing. you got lucky
  22. Replies
    9
    Views
    633

    Cam will add some nice rumble if you have rear...

    Cam will add some nice rumble if you have rear exhaust :)
  23. Replies
    3
    Views
    364

    It should help some, but the biggest loads are...

    It should help some, but the biggest loads are often side loads when turning towing a tube.
    Good work though!
  24. Replies
    5
    Views
    317

    The 160 thermostat just gives you a bit more run...

    The 160 thermostat just gives you a bit more run up room since it will cool down to lower temperature. It does not lower the temperature at speed.
  25. Replies
    26
    Views
    6,834

    Easy...

    Easy fixhttp://greenhulk.net/forums/attachment.php?attachmentid=462916&stc=1
Results 1 to 25 of 320
Page 1 of 13 1 2 3 4