Search

Type: Posts; User: superair

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    33
    Views
    3,187

    Condolences to his friends and family. As others...

    Condolences to his friends and family. As others have stated I always took his advice without question; very knowledgeable.
  2. Thread: Aem 30-4900

    by superair
    Replies
    3
    Views
    382

    I couldn't get it to work

    I couldn't get it to work
  3. Replies
    4
    Views
    456

    Your craft is not gel coat. It has base coat and...

    Your craft is not gel coat. It has base coat and clear coat just like a car. Someone will have to fill and sand the area then repaint it. Any body shop can do that for you.
  4. Replies
    1
    Views
    221

    I would get reducer barbs

    I would get reducer barbs
  5. I am not sure when it started but at least in...

    I am not sure when it started but at least in 2003 the company I work for quoted Yamaha painting of all their PWC's.
  6. yes

    yes
  7. Replies
    14
    Views
    944

    looks to be about an 08 model. The HIN number...

    looks to be about an 08 model. The HIN number should be found on the right rear corner where the pad is
  8. Replies
    10
    Views
    920

    If nothing else it keeps the water out of the...

    If nothing else it keeps the water out of the area. I thought it was more to lubricate the seals against the shaft rotations.
  9. Replies
    10
    Views
    920

    I filled mine with grease as I was putting it...

    I filled mine with grease as I was putting it back together. Once a year after that I add just one pump with my grease gun.
  10. Replies
    104
    Views
    7,535

    I purchased the upgraded pump from Dean. Probably...

    I purchased the upgraded pump from Dean. Probably the same one he sold you. I did not change the fuse. A larger fuse will not get anymore current to the pump it will just take more current to blow...
  11. Replies
    28
    Views
    2,314

    You press against the shaft on the other end. Not...

    You press against the shaft on the other end. Not the back of the coupler
  12. Replies
    28
    Views
    2,314

    I used a 1" PVC cap against the coupler. It...

    I used a 1" PVC cap against the coupler. It doesn't take a whole lot of pressure to press it in but my press would not go in between the fingers. On the shaft side coming out I just used a scrap...
  13. Replies
    28
    Views
    2,314

    yes, I rebuilt two this year both without...

    yes, I rebuilt two this year both without removing the coupler
  14. Replies
    86
    Views
    19,248

    So with this design if the impeller is stuck how...

    So with this design if the impeller is stuck how easy will it be to heat it? Looks like it might require the shaft to be removed.
  15. Replies
    6
    Views
    389

    It wasn't correct but I used a four way lug...

    It wasn't correct but I used a four way lug wrench centered on the coupler to grab four of the points and then used the driveshaft to hold the other end with a strap wrench around it and then into a...
  16. Replies
    6
    Views
    389

    It's a somewhat time consuming job being that you...

    It's a somewhat time consuming job being that you have to move the motor to remove the shaft assembly. No you don't have to completely remove the motor though. Pull the pump then move the motor off...
  17. Replies
    6
    Views
    423

    SOLD I have a take off with zero hours from a 2017...

    I have a take off with zero hours from a 2017 GP1800. I'll take $200 plus shipping
  18. Replies
    13
    Views
    1,244

    You should.

    You should.
  19. Replies
    17
    Views
    874

    FS Well he just called and he sold the GP not...

    Well he just called and he sold the GP not running so I won't be needing the starter. Thanks for the reply.
  20. Thread: Paint bubbles

    by superair
    Replies
    36
    Views
    2,186

    Thanks for the clarification; so on my SHO 2008...

    Thanks for the clarification; so on my SHO 2008 it should not be a check valve? That is the one I could blow through. I guess I never tried it on the GP; anyway I disconnected the bilge siphon in...
  21. Thread: Paint bubbles

    by superair
    Replies
    36
    Views
    2,186

    that one appears to just be a joint not a check...

    that one appears to just be a joint not a check valve. you can blow through it either way.
  22. Replies
    17
    Views
    874

    FS price?

    price?
  23. Replies
    17
    Views
    874

    FS 800, sorry

    800, sorry
  24. Thread: Paint bubbles

    by superair
    Replies
    36
    Views
    2,186

    While I agree that the siphon system will not...

    While I agree that the siphon system will not work properly or even at all I do not agree that there is a real risk in the bilge filling from the siphon back flow out through the strainer (pickup)....
  25. Replies
    17
    Views
    874

    FS Do you have a starter?

    Do you have a starter?
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4