Search

Type: Posts; User: bainer1290

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    100

    WTB Thanks! Hoping to track down a used set of VF3 or...

    Thanks! Hoping to track down a used set of VF3 or Boyesen/Riva Stuffers
  2. Replies
    53
    Views
    2,415

    Was able to clean and check specs on the crank...

    Was able to clean and check specs on the crank today. Big end side clearance, small end free play and crank width were all right in the middle of the ranges from the service manual. I then spun all...
  3. Replies
    53
    Views
    2,415

    Cool thanks for confirming that!

    Cool thanks for confirming that!
  4. Replies
    53
    Views
    2,415

    Sorry I should have explained that better so yes...

    Sorry I should have explained that better so yes the reed cages and reeds were from the 1300, but the intake plate that the 3 reed cages bolt onto was that the intake from your 1200 or was it from a...
  5. Replies
    2
    Views
    100

    WTB Gp1300r Gp1200r Reeds

    Looking for a set of reeds for my GP1200r build, could be stock GP1300r cages/reeds or Carbon Tech, Vforce, maybe M16's but would need the spacer too. Anyways let me know what you have. Thanks
  6. Replies
    7
    Views
    290

    WTB Still looking for Flame Arrestors Reeds...

    Still looking for
    Flame Arrestors
    Reeds (could be GP1300r stock or aftermarket 1200/1300)

    Let me know if you have either, thanks!
  7. Replies
    53
    Views
    2,415

    Sounds like stock hold up and the carbon ones...

    Sounds like stock hold up and the carbon ones chip with low hours as they are close to the crank turbulence without a spacer. Did you use the GP1200r reed plate or will I need the 1300 plate to mount...
  8. Replies
    53
    Views
    2,415

    Good to know, I will try to find some 1300 cages,...

    Good to know, I will try to find some 1300 cages, did you install oem reed petals or did you go with carbon aftermarket reeds?
  9. Replies
    53
    Views
    2,415

    Can Gp1300R reed cages/reeds be used in a GP1200R...

    Can Gp1300R reed cages/reeds be used in a GP1200R engine? Are they the same or is there an advantage to one over the other?
  10. Replies
    53
    Views
    2,415

    You should try the For Sale section instead of my...

    You should try the For Sale section instead of my rebuild thread...
  11. Replies
    53
    Views
    2,415

    Good call, I actually looked in my tool...

    Good call, I actually looked in my tool collection and found a bore gauge! haha forgot I had that. Anyways all the bores are in great shape with nearly zero change in diameter top to bottom, measured...
  12. Replies
    7
    Views
    290

    WTB Thank you but got the impeller last week. Still...

    Thank you but got the impeller last week. Still looking for:
    -Reed Petals (prefer carbon)
    -Milled or Aftermarket Head
    -Flame Arrestors / Adapters
  13. Replies
    53
    Views
    2,415

    I now have all 3 oem used 66V cylinders that are...

    I now have all 3 oem used 66V cylinders that are in great shape. I want to use new ProX pistons and the numbers stamped in the top of each cylinder is 8, 10 and 14. Cross referencing this to ProX the...
  14. Replies
    7
    Views
    290

    WTB Thanks for the heads up, yes I did. I ended...

    Thanks for the heads up, yes I did.

    I ended up finding a Riva Rideplate and YF CF 19/19 prop used on ebay, so now only looking for:
    -Reed Petals (prefer carbon)
    -Milled or Aftermarket Head...
  15. FS - Parts How much for the trim tabs?

    How much for the trim tabs?
  16. Replies
    53
    Views
    2,415

    I've been doing some research on the pump tunnel...

    I've been doing some research on the pump tunnel reinforcement, looks like its a good thing to do before anything happens. I will also replace those pump shoe threaded mounts to the 05+GP1300 ones...
  17. Replies
    53
    Views
    2,415

    I pulled the pump today, the prop is a stock 66V...

    I pulled the pump today, the prop is a stock 66V according to the stamp on it. I got the grate, rideplate and shoe out without any problems, does not appear that they were sealed yet so good that I...
  18. Replies
    53
    Views
    2,415

    I am planning to setup the ski similar to the...

    I am planning to setup the ski similar to the Riva Stage 2 https://rivaracing.com/i-18268337-gp1200r-stage-2-kit.html which will be quicker than stock but I am not really trying to set a top speed...
  19. Replies
    53
    Views
    2,415

    Nice thanks for the pic! I like that idea because...

    Nice thanks for the pic! I like that idea because its free and I can then wait to find a deal on F/A's one day.
  20. Replies
    53
    Views
    2,415

    Cool I will see if I can find that post, and yes...

    Cool I will see if I can find that post, and yes I saw the set on ebay for $170, thats not too bad its an option but I figured I would see what other options are out there.
  21. Replies
    53
    Views
    2,415

    Starting to look at flame arrestors, seems tough...

    Starting to look at flame arrestors, seems tough to find used sbn 44 adapters and 3 F/A's on ebay or in the clasifieds here. I have read that a few have used the stock air box, but removed the intake...
  22. Replies
    11
    Views
    1,005

    FS - Parts I got this same PM just 2 hours ago for a WTB ad...

    I got this same PM just 2 hours ago for a WTB ad I posted. Thanks for letting me know!
  23. Replies
    7
    Views
    290

    WTB Thanks but looking for the 13/19.

    Thanks but looking for the 13/19.
  24. Replies
    7
    Views
    290

    WTB GP1200R Stage 2 Parts

    Looking for parts for a 2000 GP1200R 66v Powervalve build:
    -3 ProX Pistons
    -Reed Petals (prefer carbon)
    -Milled or Aftermarket Head
    -Flame Arrestors / Adapters
    -Riva Ride Plate
    -Pump Seal Kit...
  25. Replies
    1
    Views
    266

    FS - Parts PM Sent

    PM Sent
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4