Search

Type: Posts; User: Super Jim

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. I think you want to "raise" the rev limiter and...

    I think you want to "raise" the rev limiter and not really "remove" it. Keep it but just raise it out of the way like 8600 or something. Then I think a 13/18 impeller will give much better...
  2. Replies
    9
    Views
    822

    I'm now running a stock clutch that has been...

    I'm now running a stock clutch that has been micro polished and cryogenically treated. So far it's holding up not enough hours on it yet to make any judgement on it..
  3. Replies
    8
    Views
    485

    Looks to be just cosmetic from the pictures and...

    Looks to be just cosmetic from the pictures and pretty normal. If you just look at the paint on these Yamaha's wrong it will scratch! In my opinion, it's an area Yamaha should have done better on...
  4. Replies
    7
    Views
    1,761

    How about on a FX for primarily spirited...

    How about on a FX for primarily spirited recreational riding?
  5. I run Macsboost air filter and velocity stack. I...

    I run Macsboost air filter and velocity stack. I love it. One straight shot into the supercharge with no 90 degree elbows to reduce air velocity. I think testing showed it flows more air than no...
  6. Replies
    16
    Views
    1,190

    More good points. I have noticed I get more MPG...

    More good points. I have noticed I get more MPG when running non-ethanol fuel for the reasons you stated above. I agree with using the higher octane E10 vs a lower octane E0 when given the...
  7. Replies
    16
    Views
    1,190

    Not exactly: Fuel stabilizers don't make ethanol...

    Not exactly: Fuel stabilizers don't make ethanol go away. it will still be there. And modern gasoline won't go bad in 6 month or a year anyway. Years ago, gasoline would turn to almost varnish if...
  8. Replies
    16
    Views
    1,487

    As you can tell from the "Chicken Strips", I...

    As you can tell from the "Chicken Strips", I don't really push it too hard. So for me the Bridgestones are just fine. I can't out ride them on the street.
  9. Replies
    16
    Views
    1,487

    new pics

    Last one sold but I'll have a couple more from the fiberglass shop next week. Here's my final version installed.
    ...
  10. Replies
    4
    Views
    452

    yes

    yes
  11. Replies
    4
    Views
    452

    Rule Low Profile. Really slick design Will fit...

    Rule Low Profile. Really slick design Will fit under the engine on the bottom of the hull
    ...
  12. Replies
    16
    Views
    1,487

    They are $220.00 + $25.00 shipping continental...

    They are $220.00 + $25.00 shipping continental U.S.
    That may seem a little high but the mold alone cost me $400.00
  13. Replies
    16
    Views
    1,487

    One left.

    One left.
  14. Replies
    16
    Views
    1,487

    You will probably like my XSR 900 then. I did a...

    You will probably like my XSR 900 then. I did a little cafe racer mod on it and tribute to...
  15. Replies
    16
    Views
    1,487

    installed

    On the water and running.http://greenhulk.net/forums/attachment.php?attachmentid=450904&stc=1
  16. Replies
    16
    Views
    1,487

    installed

    And here it is on the...
  17. Replies
    16
    Views
    1,487

    finished

    Here are some pics with the holes cut and vent tubes installedhttp://greenhulk.net/forums/attachment.php?attachmentid=450899&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=450900&stc=1
  18. Replies
    16
    Views
    1,487

    FX Heat extraction rear racing seat

    Years ago I made some fiberglass rear seats for the Honda F15X to help remove heat from the hull. I decided to do the same for the Yamaha FX and make some improvements from my first design.

    I...
  19. Thread: Oil in SVHO?

    by Super Jim
    Replies
    7
    Views
    666

    Rotella T4...

    Rotella T4
    https://rotella.shell.com/en_ca/products/conventional-motor-oil/rotella-triple-protection.html
  20. Replies
    9
    Views
    800

    They need to know the required services have been...

    They need to know the required services have been completed as scheduled. It doesn't mean it has to be performed by Yamaha but you may need to prove it was performed in the event of a major warranty...
  21. Replies
    9
    Views
    800

    Absolutely no reason as long as you keep your...

    Absolutely no reason as long as you keep your receipts and document you did it for warranty reasons. No need to change the plugs either.

    You will end up saving about $250 - $275.00 depending on...
  22. need a measurement on a 2016 FX SVHO please

    http://greenhulk.net/forums/attachment.php?attachmentid=450571&stc=1If someone has a blue 2016 FX SVHO that can take a couple measurements I would appreciate it. I out of town but looking for the...
  23. Replies
    5
    Views
    491

    What is the difficulty level of changing the oil...

    What is the difficulty level of changing the oil cooler?

    I can't get it changed by a dealer under warranty for a couple weeks and I have a 200 mile ride coming up next weekend. I've been checking...
  24. Replies
    30
    Views
    12,636

    What all is involved in changing the oil cooler? ...

    What all is involved in changing the oil cooler? Looks like removal of the exhaust and not a quick job?
  25. Replies
    5
    Views
    491

    Thanks. Do you know if Yamaha will replace it no...

    Thanks. Do you know if Yamaha will replace it no questions asked or must I have the extended warranty?
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4