Search

Page 1 of 3 1 2 3

Search: Search took 1.00 seconds.

  1. Replies
    55
    Views
    1,313

    Tie the ski down to the trailer or to something...

    Tie the ski down to the trailer or to something solid.

    Start the engine and adjust one low speed adjuster for highest idle RPM.

    Adjust the throttle stop screw to bring the RPM back to spec.
    ...
  2. You need to get your hands on a repair manual.

    You need to get your hands on a repair manual.
  3. Replies
    11
    Views
    339

    There is a misconception that high octane fuel is...

    There is a misconception that high octane fuel is more explosive than low grade fuels. This is completely opposite.

    Octane rating has to do with how explosive fuel is, but the lower the number,...
  4. Yes, that's what he means. Switch your MAG...

    Yes, that's what he means.

    Switch your MAG plug wire with the CEN plug wire and see if the cylinder the cylinder that doesn't fire changes.

    Have you ohm tested the magneto since you replaced...
  5. Replies
    22
    Views
    1,309

    Those pieces are made of stainless, but you can...

    Those pieces are made of stainless, but you can try aluminum.

    You can try patching it, but it's not fiberglass. It's actually SMC (sheet molded composite)

    You can try using fiberglass to fill...
  6. Replies
    8
    Views
    399

    Fine, I wrote gasket. Maybe i should have said a...

    Fine, I wrote gasket. Maybe i should have said a seal.
  7. Replies
    16
    Views
    733

    Well, I sent him a EMM that wouldn't start the...

    Well, I sent him a EMM that wouldn't start the ski. I got back an EMM that starts it now. It will be couple months before I can get you a performance update.

    I will say his communications and...
  8. Replies
    6
    Views
    627

    Get a hold of Bruce and see if he has any props...

    Get a hold of Bruce and see if he has any props laying around, or can recommend?

    http://www.wetwolf.com/about.html
  9. Replies
    16
    Views
    733

    I was asked to share my experience, so here it...

    I was asked to share my experience, so here it goes.

    When I had the 2003 MSX 140, I bought a spare EMM and injectors from a member who will remain unnamed. Cost around $500 a few years ago. With...
  10. Replies
    5
    Views
    427

    Another option is they rebuilt the engine with...

    Another option is they rebuilt the engine with oversized pistons and never modified the domes
  11. So does that mean you they are no longer offered?...

    So does that mean you they are no longer offered?

    I never saw this thread and have a set of PSI cylinders that could use this set up.

    PS: Long time no see, hope everyone is doing well
  12. Replies
    55
    Views
    1,313

    Was there extra head pipes in the parts you...

    Was there extra head pipes in the parts you picked up? I thought there might be.

    Yep, the sole reason we recommend new owners go through EVERYTHING when they buy a used ski. You're living proof of...
  13. Replies
    6
    Views
    369

    Welcome. The SS 6 vane pump is very common....

    Welcome.

    The SS 6 vane pump is very common. Nothing unusual there.

    All Polaris pumps use a wedge between the pump and exit nozzle. Make sure it's installed correctly though. Thin part at the...
  14. Replies
    42
    Views
    1,073

    You need a new circuit board. It's completely...

    You need a new circuit board. It's completely rusted out. No need to continue diagnosing until you replace that IMO.
  15. Replies
    1
    Views
    290

    Yes. 94 SLT 750 hull is made of fiberglass and...

    Yes. 94 SLT 750 hull is made of fiberglass and almost 70 lbs lighter if I remember correctly. The 750 makes 80 HP and will do about 48-50 MPH. It's also very difficult to find an aftermarket ride...
  16. Spark plugs are cheap insurance. Make sure to...

    Spark plugs are cheap insurance.

    Make sure to remember the DRAIN plug!!!!

    Ramps are a fun place to be at the beginning of the season.

    Backing trailer up arguments, backing vehicle up too far...
  17. Replies
    6
    Views
    622

    Welcome to the Hulk. Where in OH are you...

    Welcome to the Hulk.

    Where in OH are you located?

    Just a FYI for you:

    650cc = 68HP and around 45 MPH

    750cc = 80HP and around 48 MPH
  18. Replies
    5
    Views
    994

    Welcome to the Hulk. I don't believe there...

    Welcome to the Hulk.

    I don't believe there were any 750's in 1996. Please verify the year by the last 2 numbers of the Hull Identification Number.

    If it is a 96, it's most likely a 780 and in...
  19. Sorry, not going through and re-reading...

    Sorry, not going through and re-reading everything.

    Is the engine mounted to the engine plate securely? The ground wire is bolted to the engine plate, which is bolted to the engine. That is the...
  20. Replies
    25
    Views
    3,656

    There really isn't a lot of gains from...

    There really isn't a lot of gains from aftermarket impellers VS. OEM

    Actually, Polaris used both Skat Trak and Nu Jet to manufacture impellers for them. (the 707 mentioned previously is a Nu Jet...
  21. Thread: Slt project

    by xlint89
    Replies
    103
    Views
    10,147

    It wasn't the best idea, but it made them both...

    It wasn't the best idea, but it made them both accessible.

    Just make sure to have the plastic cover in place between the box and battery.

    I've been running mine like this for quite a few years...
  22. Replies
    13
    Views
    1,479

    Love it. Legend oil smells sooooo good. I...

    Love it. Legend oil smells sooooo good.

    I don't mind having a little extra oil in the crankcase.

    The extra room under the hood from eliminating the oil tank is nice.

    Don't need to worry...
  23. Replies
    3
    Views
    497

    I cannot say for sure on the 1999 model, but on...

    I cannot say for sure on the 1999 model, but on the 97 and 98 (basically the same) the engine doesn't need to come out.

    The tank will come out the hood when the fuel sender is removed from the...
  24. Replies
    9
    Views
    420

    Exactly ^^^^ I've had a magneto for your...

    Exactly ^^^^

    I've had a magneto for your machine for sale for a few years now. Shame you had to order one. Hope it didn't cost a lot.
  25. 1997 had 38mm carbs. Installing a set of 40mm...

    1997 had 38mm carbs.

    Installing a set of 40mm might be part of your bog problem.
Results 1 to 25 of 59
Page 1 of 3 1 2 3