Search

Type: Posts; User: bainer1290

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    84
    Views
    5,548

    Well good news the engine is now tight! Held 6psi...

    Well good news the engine is now tight! Held 6psi with no loss for 6 minutes, after 30 mins it was at 5.6psi, then at an hour 5.25psi.

    Next up a compression test then I will be dropping it back...
  2. Replies
    84
    Views
    5,548

    Thats good to know, I have no experience with the...

    Thats good to know, I have no experience with the copper spray.
  3. Replies
    84
    Views
    5,548

    Appreciate the advice! I tore it down and hit the...

    Appreciate the advice! I tore it down and hit the base gaskets and pv covers with 3bond. Hoping the next pressure test will be tight.
  4. Replies
    84
    Views
    5,548

    Question on pressure testing as I want to...

    Question on pressure testing as I want to clarify.

    I read the sticky http://greenhulk.net/forums/showthread.php?t=9408
    and the Group K article https://www.groupk.com/airleak.html

    One says the...
  5. Replies
    84
    Views
    5,548

    Engine assembly complete, pressured tested good...

    Engine assembly complete, pressured tested good to go!

    Next need to rebuild the carbs and then its time to drop the engine back in the hull.
    ...
  6. Replies
    84
    Views
    5,548

    Got the motor partly built over the past few...

    Got the motor partly built over the past few weekends. Its coming together good so far!...
  7. Replies
    84
    Views
    5,548

    Sounds great, I know what you mean about the...

    Sounds great, I know what you mean about the waterbox and hose routing in the rear its tight back there lol
  8. Replies
    84
    Views
    5,548

    Ok so I would have 4 pissers? The stock ones from...

    Ok so I would have 4 pissers? The stock ones from the pipe under the rub rail on the port and starboard sides. Then I will add 2 on the rear for the 2nd and 3rd cylinders?



    I added a 3/8 thru...
  9. Replies
    84
    Views
    5,548

    What's the best cooling setup for a stage 2...

    What's the best cooling setup for a stage 2 modified GPR with the holeshot kit installed?

    As I will be using Riva heads I have 3 outlets on the heads along with the stock single pipe with 2 inlets...
  10. Replies
    2
    Views
    174

    SOLD Got one, thanks again Richard!!

    Got one, thanks again Richard!!
  11. Replies
    2
    Views
    174

    SOLD SHO or Riva Steering Nozzle for GPR

    Looking for a steering / exit nozzle, let me know if you have one to sell. Thanks
  12. Replies
    84
    Views
    5,548

    Sounds good thanks!

    Sounds good thanks!
  13. Replies
    84
    Views
    5,548

    Figured out where the styrofoam goes! ...

    Figured out where the styrofoam goes!

    http://greenhulk.net/forums/attachment.php?attachmentid=470687&stc=1
  14. Replies
    84
    Views
    5,548

    I need to see a pic of where that ? Styrofoam...

    I need to see a pic of where that ? Styrofoam piece fits then, it has to fit somewhere.

    http://greenhulk.net/forums/attachment.php?attachmentid=470606&stc=1
  15. Replies
    84
    Views
    5,548

    Yes I am planning to do the Oside recipe 125...

    Yes I am planning to do the Oside recipe 125 mains, 110 pilots, 1.5 Needle and Seat, 95 gram spring. I was planning to disable the Accelerator Pump, Drilled Return Pressure Balancing Mod with a jet...
  16. Replies
    84
    Views
    5,548

    Yes I have heard the free flow is not needed...

    Yes I have heard the free flow is not needed unless you have a heavily modded motor so I am not planning to do that.
  17. Replies
    84
    Views
    5,548

    Question on the rear exhaust styrofoam, the piece...

    Question on the rear exhaust styrofoam, the piece that I have in the middle of this pic with the ? seems to fit in a little loosely, is this the right place for it to go?
    I should have take a...
  18. Replies
    84
    Views
    5,548

    Got the pump reassembled today with the...

    Got the pump reassembled today with the additional pump feed for the holeshot kit. Installed the Riva ride plate and extended Trim Tabs. Shimmed the plate a little on the front and the trim tabs to...
  19. Replies
    8
    Views
    437

    2-Stroke It looks like we are doing similar builds, mine...

    It looks like we are doing similar builds, mine is a 2000 GP1200R. Check out my thread you will find some recommendations and useful tips from other forum members. I opted to do the tunnel...
  20. WTB - Parts Thank you WFO for the Jetworks Valve. Still...

    Thank you WFO for the Jetworks Valve.

    Still looking for the exhaust gasket if anyone has one let me know!
  21. WTB - Parts WTB - Adjustable Jetworks Valve & GPR Holeshot Gasket/Plate

    I'm adding a Holeshot kit to my GP1200R, need a 3/8 adjustable jet works valve and an exhaust blockoff plate like the ones Gus used to make and sell on here. Anyone have either to sell? Thanks
    ...
  22. Replies
    84
    Views
    5,548

    Well its been a while since I last updated, sorry...

    Well its been a while since I last updated, sorry for the delay!

    Good news my crank checked out in great shape, needed a slight truing but is now true, welded and on its way back to me. I also...
  23. Replies
    84
    Views
    5,548

    Starting to get the parts together for the build!...

    Starting to get the parts together for the build! Riva heads with Girdle kit and fresh paint, F/A's, Rideplate and Intake grate!

    Waiting on the Pro-X pistons, was able to order 2 but the 3rd is...
  24. Replies
    2
    Views
    162

    WTB Thanks! Hoping to track down a used set of VF3 or...

    Thanks! Hoping to track down a used set of VF3 or Boyesen/Riva Stuffers
  25. Replies
    84
    Views
    5,548

    Was able to clean and check specs on the crank...

    Was able to clean and check specs on the crank today. Big end side clearance, small end free play and crank width were all right in the middle of the ranges from the service manual. I then spun all...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4