Search

Thanks for the advice blakegjones ,boudin


I try to make timing for second time and I end up with:




http://greenhulk.net/forums/attachment.php?attachmentid=455817&stc=1

Can anyone see my timing if it is correct or not ?


http://greenhulk.net/forums/attachment.php?attachmentid=455691&stc=1

http://greenhulk.net/forums/attachment.php?attachmentid=455692&stc=1 ...

Hi

I install the engine completely but how to make engine timing I read from my service manual but I confuse. Anyone can tell me how to do it by steps.


Thank you

Thanks for everybody

Hello

The job is done I try for last time with using flat screw driver and my fingers and it come down in it place and now installing the cylinder head.


thank you

Yes, I know that it go in from the bottom and when I use the zip ties I put each one on the ring and when I put the cylinder the zip tie slide down and the rings open again.


thank you

Hi,

Anybody can tell me how he install the cylinder inside the piston ?
I use tight cable and it not work I made tool from thin metal and also, It is not work I use my finger one piston get...

I think you should replace bolts with nuts if you tighten them because they are stretch when you tight them and in cars the same thing and there is a special tool to measure how much it stretch and...

thank you blakegjones

No, I have the service manual and I know that if my crankcase have no mark and the crankshaft have mark I should got black bushing as I see from my service manual and if my con rod have mark and...

Hello everybody

I buy new crankshaft from Kawasaki dealer but before this. I bought new bushing from the dealer and they choose it for me after I bring my used crankshaft with the crankcase to...

Thank you for your explanation.

Now, I have another problem the oil pump shaft come inward and outward by hand is this normal ?

Thanks for everybody

Ok, now I understand I should do Myself method like what he say I should turn wrench from straight 0 degrees until wrench points to 120 degrees no matter where nut corner...

But, not all nuts are one corner is straight (0 degree) some of them between of straight (between 0 degree) .

how can I tight them

...

Hello everybody

Today I install the new connecting rod on my new crankshaft but the problem was after I tight them 21.6 N.m with torque wrench I dont know how to tight the nut 120 degree more.
...

Yes ,the failure on my original motor involved spun and these are the pictures of the two connecting rod:
...

Hello everybody


Today when I assemble my ultra 250x 08 engine I face this problem , there are two connecting rod the caps does not fit on them and when I try to install it in my new crankshaft...

Hello everybody

Finally, I end with buying new crankshaft but now I want to be sure if my engine case is in good condition or not. And if any one have advise tell me before I start rebuild.
...

Hi,

I want Kawasaki 13107-0728 impeller shaft or 13107-0764 to upgrade my ultra 250x jet pump. Anyone know online site or person sell it around $45.

thank you

Wow excellent thread !!! I work in same project and its also, 08 250x ultra

I hope not face the same problem because I spent until now 2k just for the parts :facepalm:

Hi,

I have kawasaki ultra 250x and the stator has no connector in it.It was removed so, I want to buy complete used stator.
And my question is there any difference between (2004-2014 STX STX12F...

Ok, how can I know if my jet pump is upgraded or not?

thank you

Hi,

I have 08 Kawasaki 250x ultra and I buy everything new include crankshaft, but my question is do I need to replace timing and oil pump chain? Also, its important to upgrade the jet pump or not...

You mean chop test or choke test?
If I open the carbs, should I rebuild them or no need ?

Thank you Teemu I will do what you say and I hope the carbs need just clean