Search

Type: Posts; User: Rescue1

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    35
    Views
    8,812

    I don't believe an auto spark would help here....

    I don't believe an auto spark would help here. The main issue is the ECM/ECU thinking things are hotter than they actually are, and giving a super lean fuel mixture. The resistor will trick it into...
  2. Replies
    35
    Views
    8,812

    I had this issue with an older 12F as it had the...

    I had this issue with an older 12F as it had the same engine and setup just a smaller stroke. I tried a new water temp sensor but it would still do the no start on hot thing. The temp sensor is...
  3. Replies
    9
    Views
    836

    All good points.. Could also be from a blown out...

    All good points.. Could also be from a blown out exhaust filter, or not blowing the water box out enough after flushing.
  4. Thread: Deposit is in!

    by Rescue1
    Replies
    0
    Views
    184

    Deposit is in!

    I put a deposit in on an LX-S, Just because of the green. 8-)8-) Many of the dealers in my area are already sold out on their low allocation amounts, which is surprising but good to hear. I will...
  5. Sticky: While I do wish they produced a bigger engine, I...

    While I do wish they produced a bigger engine, I will be putting a deposit on a green one this week. I love the Ultra hull as the water I ride in is always rough, and am really digging the new look...
  6. Replies
    6
    Views
    723

    I didn't but that's a good idea. I will take it...

    I didn't but that's a good idea. I will take it out soon and see what I can figure out. Probably due for a cleaning anyway. :smt119 Just forward thinking a bit.. If the I/C is shot is there...
  7. Replies
    6
    Views
    723

    Plugs are new but I will get a shot of the piston...

    Plugs are new but I will get a shot of the piston tops with my stick cam. :hurray:
  8. Replies
    6
    Views
    723

    Ultra300 Rough after starting issue..

    Hello all,

    My 2012 Ultra 300x just keeps going which is a good thing. I am at 200 hours and the only Mod is a DIY SCOM. I've had an issue since last summer I'd like to finally address. After I...
  9. I still have my doubts but still hope I am wrong.

    I still have my doubts but still hope I am wrong.
  10. Replies
    12
    Views
    1,542

    Can you post a Pic of the JetSki? I saw you post...

    Can you post a Pic of the JetSki? I saw you post it locally on Facebook but can't find the post.. I only ride Kawasaki and as we all know you hardly ever see any other Kawis around, so when I see one...
  11. Replies
    3
    Views
    399

    Check the hoses going to the Oil cooler by the...

    Check the hoses going to the Oil cooler by the filter. They tend to split in that area.
  12. Replies
    17
    Views
    1,648

    You may have luck with various reverse taps, EZ...

    You may have luck with various reverse taps, EZ outs ETC. I've had decent luck, sometimes the head has to come off. I'd suggest a factory service manual because there is a lot of into you need to...
  13. Thread: NGK PMR9B

    by Rescue1
    Replies
    4
    Views
    729

    How's your compression?

    How's your compression?
  14. Replies
    18
    Views
    1,696

    100% that damned ISC solenoid, not so much a...

    100% that damned ISC solenoid, not so much a stepper motor.. Sometimes you can clean it out and get the plunger to move freely, however most I've seen the windings in the electro magnet side get...
  15. Replies
    2
    Views
    404

    I have worked on boats for a long time that are...

    I have worked on boats for a long time that are in and around saltwater and unless the bolt/nut is big and I have full access to the front and back of same I DO NOT use any locktite, especially on...
  16. Replies
    7
    Views
    1,045

    Yeah the old ones had a steering Hall effect...

    Yeah the old ones had a steering Hall effect sensor that would give it a little throttle via a valve on top of the throttle body. I can assume that the new ones have a similar sensor however the ECU...
  17. Replies
    7
    Views
    1,045

    Are you turning the handlebars at all while this...

    Are you turning the handlebars at all while this happens? Even a little
  18. Replies
    8
    Views
    866

    Yes the earlier outboards had Ficht, and what a...

    Yes the earlier outboards had Ficht, and what a troublesome setup it was... But wow, I saw the links about about BRP shutting down the outboard manufacturing.. I guess I am surprised and not at the...
  19. Replies
    45
    Views
    3,948

    This may not be the issue but... I've seen plenty...

    This may not be the issue but... I've seen plenty of wires in cars that check correctly with voltage using a DMM or a low current test light.. However if you take a headlight bulb with 2 pigtails...
  20. Replies
    4
    Views
    527

    I know being in Florida you don't know what this...

    I know being in Florida you don't know what this term means(Yes I am jealous) but when I winterize my JetSki I put 1 or 2 of those damp rid containers in the hull and cover it all up. They seem to...
  21. Replies
    8
    Views
    866

    View Post

    Personally I canít stand anything made by BRP. Iím saying this as I rebuild another damned Can Am ATV.

    Anyway, the early ETechs were problematic, the most notable were the FICHT fuel systems,...
  22. I suppose if it helps with those F%^#$@ crappy...

    I suppose if it helps with those F%^#$@ crappy rocker arms they had on the early, and likely still current Pentastar engines it should help with flat tappets.
  23. Replies
    2
    Views
    323

    Rough idle after startup question

    Hello all,

    2012 300X, 150 hours, SCOM and no other mods. I change the exhaust filter every 2 years out of habit as well as the plugs..

    When I go to start the engine after shutting it down while...
  24. Replies
    4
    Views
    452

    I ended up putting all new Gates hose in. Pulled...

    I ended up putting all new Gates hose in. Pulled the intake off, cleaned the injectors as well while there. Everything is back up and running now. Thanks for the advice guys..:smt066
  25. Replies
    8
    Views
    896

    Salt away isn't strong enough to unclog passages...

    Salt away isn't strong enough to unclog passages that are already in the engine. I'm not sure if vinegar works as I've never tried it but most of the ports I've cleaned were manually done, a pain I...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4