Search

Type: Posts; User: jsmith7364

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    20
    Views
    2,356

    I have the retainers and getting ready to put...

    I have the retainers and getting ready to put them in. It is just a peace of mind for me at this point for when the ski comes unhooked. I was just curious about the wheel. I am seeing about...
  2. Replies
    20
    Views
    2,356

    Will the 135 wheel require upgraded injectors?...

    Will the 135 wheel require upgraded injectors? Fuel pump or regulator?
  3. I have a 2018 GTX and a 2021 RXPX

    I have a 2018 GTX and a 2021 RXPX
  4. [QUOTE=Green Hulk;3147759]Two very simple mods...

    [QUOTE=Green Hulk;3147759]Two very simple mods that made so much difference! The sponsons and steering upgrade completely transformed this ski.

    Jerry, while I understand the brand wars with parts....
  5. OK so here is some updated test results for my PX...

    OK so here is some updated test results for my PX and the 13/15. After the last test I pulled the impeller to check it out and swap out the wear ring. Previously I had a bad wear ring and needed...
  6. Two things. I have seen Bishop Phillips bend...

    Two things. I have seen Bishop Phillips bend over backwards to make things right with customers. So this sounds only only half the story. And the second thing is that IF you had filed a claim with...
  7. It is never bad to change your oil early except...

    It is never bad to change your oil early except to your wallet. Does it help or hurt to change it early? Folks been argueing that since the dawn of time and it won't stop anytime soon. According...
  8. If I was not reaching the 8200-8400 rpm range I...

    If I was not reaching the 8200-8400 rpm range I would agree with you that it was a heat issue. But with those rpm's, it has to be something else. I am going to tweak the impeller a bit to see if I...
  9. 21 px

    21 px
  10. So, with new impeller 13/15 it hits 8200 rpm and...

    So, with new impeller 13/15 it hits 8200 rpm and 74 on the dash. It was mid to low 80’s with low humidity in the DFW area. So I dropped 200 rpm but gained +2 mph. Which is still lower than a...
  11. That's ok. It has to be something simple that is...

    That's ok. It has to be something simple that is wrong.

    New impeller is in, nothing wrong with stainless wear ring. Went ahead and put the intercooler hoses in that I had left over from my GTX...
  12. Which is the reason I am trying different things.

    Which is the reason I am trying different things.
  13. 2021 RXPX, intake, tune (8500 Riva), catch can,...

    2021 RXPX, intake, tune (8500 Riva), catch can, intake girdle, valve retainers for piece of mind.

    With a stock impeller 13.6/24 it wasn't seeing but 74mph/8200rpm. Granted it has been hot and...
  14. Thanks, ordered it last night and it looks like...

    Thanks, ordered it last night and it looks like it shipped today. Won't know for sure until the tracking is updated. Worst case it won't ship until tomorrow and I should have it before the weekend.
  15. If I purchase this can I pick it up at Mudbug?

    If I purchase this can I pick it up at Mudbug?
  16. Replies
    15
    Views
    1,540

    Just wanted to clarify that you have to...

    Just wanted to clarify that you have to completely remove the column to get to where you grease it?

    By chance did you see anyplace that would be good to install a grease fitting so you don't...
  17. Replies
    7
    Views
    1,238

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=476581&stc=1
  18. Replies
    3
    Views
    537

    I have not seen a ST3 hull ski made out of...

    I have not seen a ST3 hull ski made out of Polytec yet. CMTech is not the same and it is a process that incorporated Fiberglass and Acrylic that is compressed and molded. The acrylic replaces the...
  19. So the PX is a shorter hull with a slight curve...

    So the PX is a shorter hull with a slight curve in the back where the hole goes through the hull. And the engine is further forward the the RXTX.


    The RXTX has a flat portion of the hull that...
  20. Replies
    11
    Views
    1,691

    I did something similar. Used the vents that I...

    I did something similar. Used the vents that I bought and cut out a circle for the ski pylon cover. And it is right above the air filter.
    ...
  21. Parts list for Garmin Fish Finder on any ST3 Hull

    Here is the parts that you need to install the FishFinder in the OEM position like the Fish Pro on any ST3 hull ski. My understanding is that this will also work with the new 2021 RXPX but I have...
  22. My 19 GTX limited cracked int he exact same...

    My 19 GTX limited cracked int he exact same place. BRP did pay for it to the amount of 3600 bucks.
  23. Replies
    11
    Views
    1,101

    I think I do want the replacement as it is under...

    I think I do want the replacement as it is under warranty, then I will order a Fizzle and put the stock 300 IC on my wifes 230 as it is better than the one on the 230.

    But they need to fix the...
  24. Replies
    11
    Views
    1,101

    I ran it for about 30 minutes on the lake, and it...

    I ran it for about 30 minutes on the lake, and it was cutting out. Put it on the trailer, strapped it down, removed the deck and put it in the water so I could run it, I had ran it for other...
  25. Replies
    11
    Views
    1,101

    .

    .
Results 1 to 25 of 60
Page 1 of 3 1 2 3