Search

Type: Posts; User: smokeysevin

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. The hull is sitting on its side now with the...

    The hull is sitting on its side now with the inside was stripped out, scuffed with 80 grit and wiped with alcohol to remove excess dust. I put one layer of 1208 fiberglass and 3:1 epoxy resin from ...
  2. Got the ski totally stripped with the exception...

    Got the ski totally stripped with the exception of the pump and driveline yesterday. I cleaned up one side of the inner engine bay and rolled the hull up on its side to try and get better access to...
  3. Well, it has come to this. My life has spiraled...

    Well, it has come to this. My life has spiraled totally out of control and I now have to actually finish projects instead of just getting more and forgetting about them.

    I got started doing some...
  4. Replies
    16
    Views
    1,147

    Do the resealed hulls flex any more than stock...

    Do the resealed hulls flex any more than stock and what did you do to separate them?

    Sean
  5. Replies
    6
    Views
    544

    You can check the microfiche online just look at...

    You can check the microfiche online just look at the part numbers. Bikebandit.com s one of the easier ones to use.

    Sean
  6. Replies
    4
    Views
    486

    I have 2 on my bench now. If I remember I will...

    I have 2 on my bench now. If I remember I will post my measurements up tomorrow.

    Sean
  7. Have yall had issues with the caps cracking near...

    Have yall had issues with the caps cracking near the threads where the hose/spout threads in? My caps all seem to die on the seam there even if I don't tighten them all that much. I have been...
  8. FS - Parts Bump Sean

    Bump

    Sean
  9. Replies
    5
    Views
    268

    Slide it on until it stops. Make sure you have...

    Slide it on until it stops. Make sure you have the rings fully seated, wrap them with a thin layer of paper tape or painters tape just enough to hold the rings in place. The factory just intalls a...
  10. Replies
    9
    Views
    532

    Thats great, thanks for posting it. Sean

    Thats great, thanks for posting it.

    Sean
  11. Replies
    77
    Views
    3,064

    Made a fixture plate to bore the kawasaki...

    Made a fixture plate to bore the kawasaki driveshaft thru hull out to fit the doo driveshaft and carbon seal carrier.

    Swag offroad tube notcher shaft(1" Version)
    3/8 Milwaukee hole saw arbor
    ...
  12. Replies
    11
    Views
    608

    I agree, the coupler is probably too close. The...

    I agree, the coupler is probably too close. The rear output shaft bearing is a pretty tight fit to the output stub shaft iirc and has the rear motor mounts cast into it.

    I have one our now of you...
  13. Replies
    2
    Views
    846

    That's cute. I have 2 like this that are probably...

    That's cute. I have 2 like this that are probably going go cost me more than they are worth to get back to good. If they hadn't been free I would have said no.

    Sean456042
  14. FS - Parts Kawasaki 4 stroke parts, pistons, cams, pumps, props.

    1 set of forged mtc pistons, stock compression ratio

    3 oem stx 15f pistons

    4 oem ultra 250 pistons

    1 modified ultra 250 155mm exit nozzle bored for nozzle rings 83mm, 84mm and 85mm rings.
    ...
  15. I was going to suggest using marine tex on the...

    I was going to suggest using marine tex on the small chunk but then I saw the keel. It my need to get flipped and re-gelkoted.

    Sean
  16. Replies
    5
    Views
    417

    WTB - Parts Pm sent Sean

    Pm sent

    Sean
  17. Replies
    7
    Views
    545

    Check the thread in my signature. If you pull the...

    Check the thread in my signature. If you pull the pumps, don't crank the motor over with the starter. Only rotate the engine by hand.

    If the gauges are bad, I can flash the ecus to 2004 spec to...
  18. Replies
    18
    Views
    774

    You can probably move it forward if you pay...

    You can probably move it forward if you pay attention to the hull while doing so. If you do move it forwards, you will increase the tongue weight so be mindful of that.

    Sean
  19. Replies
    27
    Views
    880

    The one I am messing with is here:...

    The one I am messing with is here: http://greenhulk.net/forums/showthread.php?t=283069

    Sean
  20. Replies
    27
    Views
    880

    Checkout koso, I am playing around with one of...

    Checkout koso, I am playing around with one of their gauges now, seems reasonably well made.

    Sean
  21. Replies
    77
    Views
    3,064

    You are correct, the fitting can either be...

    You are correct, the fitting can either be silicone'd to the bulkhead (as stock does) or you can use the bulkhead washer as the fitting does in other applications.

    One other think I am...
  22. Replies
    77
    Views
    3,064

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=455791&stc=1
    Dimensions are based on aeromotive fittings and 2008 rxt-x steering cable. Kawasaki cables are a little smaller in diameter but...
  23. Replies
    37
    Views
    10,118

    If my memory is correct, when this was brought up...

    If my memory is correct, when this was brought up a few years ago it came down to the seating position being the issue. Basically they claimed it was because you were riding on the pwc vs in a boat...
  24. Last time I looked they were like $120 Sean

    Last time I looked they were like $120

    Sean
  25. Replies
    77
    Views
    3,064

    I may have figured out a way to make control...

    I may have figured out a way to make control cable thru hull fittings for relatively little money.

    Start with a -10an bulkhead fitting and hard line nut.

    Drill the an fitting through with a...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4