Search

Type: Posts; User: BigDaddyRXP

Page 1 of 8 1 2 3 4

Search: Search took 0.07 seconds.

  1. A much lighter wallet!

    A much lighter wallet!
  2. Replies
    6
    Views
    1,097

    Those are washers from an 2008 kit. ... it's...

    Those are washers from an 2008 kit.
    ... it's time for a rebuild!
  3. Replies
    13
    Views
    1,731

    You could probably pitch that 14/19 and make it...

    You could probably pitch that 14/19 and make it work, but an out of the box 15/20 will get you way closer to target rpm with less tweaks (if even needed at all).
  4. Replies
    13
    Views
    1,731

    With a rev limit set at 8350 the ecu begins to...

    With a rev limit set at 8350 the ecu begins to pull fuel and timing when you get much over that limit in attempts to slow down the engines rpm's. It doesn't take long to blow a head gasket when your...
  5. Replies
    13
    Views
    1,731

    Considering it sounds like your right at 300 rpm...

    Considering it sounds like your right at 300 rpm to high.... I'd start with a 15/20 and pitch from there if needed for a target rpm of 8250-8300
  6. Replies
    13
    Views
    1,731

    You need some prop work done (or a new one).......

    You need some prop work done (or a new one).... your running way past your rev limiter!
  7. Replies
    118
    Views
    57,484

    BRP released turbo side by sides years ago...

    BRP released turbo side by sides years ago...
  8. Replies
    5
    Views
    1,538

    Try a new battery. If you left a Battery Tender...

    Try a new battery. If you left a Battery Tender on it for months, it probably cooked the cells down. Yes..... Battery Tenders will cook down vented batteries.
  9. Thread: 2005 Rxp

    by BigDaddyRXP
    Replies
    2
    Views
    512

    No boost. Super charger problem more than likely.

    No boost. Super charger problem more than likely.
  10. Replies
    14
    Views
    1,643

    Just slides into the PTO.

    Just slides into the PTO.
  11. Replies
    34
    Views
    6,760

    The problems now are no longer really in the...

    The problems now are no longer really in the clutch set-up.... it's the bearings. BRP extended the rebuild time from 100 hours to 200 and the bearings didn't change at all. The bearings used are...
  12. Replies
    31
    Views
    3,224

    I find it very highly unlikely that BRP is (now)...

    I find it very highly unlikely that BRP is (now) contracting SBT to build their re-manufactured engines! Nothing OEM goes into SBT rebuilt engines.... no way would BRP be responsible-liable nor...
  13. Replies
    6
    Views
    1,098

    Jerry's getting cheap! I asked him for a T...

    Jerry's getting cheap!

    I asked him for a T shirt years ago..... and the bastard sent me a Yamalog T shirt :facepalm:...... :lol:
  14. Replies
    44
    Views
    4,228

    That things a mess! You'll probably never get...

    That things a mess! You'll probably never get that hat off the drive shaft without cutting it off.
  15. Replies
    19
    Views
    2,810

    Same shit happened to me back in 2010. We went...

    Same shit happened to me back in 2010. We went out there for 5 days, and I lost a rear charger bearing on a brand new ET charger 2 hours into the first days ride. My ski sat in Jerry's garage the...
  16. Replies
    7
    Views
    1,098

    You running open loop?

    You running open loop?
  17. Replies
    8
    Views
    1,355

    It's already up to a 309 now?

    It's already up to a 309 now?
  18. Replies
    13
    Views
    2,971

    Something that couldn't pass through the blades...

    Something that couldn't pass through the blades beat the shit out of that charger..... look at the inlet on the front cover. It's a wonder that charger didn't come apart from being way out of...
  19. Replies
    8
    Views
    1,355

    What ski???

    What ski???
  20. Replies
    5
    Views
    1,277

    Definitely not OEM! What is that on?

    Definitely not OEM!

    What is that on?
  21. Replies
    3
    Views
    726

    Good luck with that. I broke all three that were...

    Good luck with that. I broke all three that were available years ago... Riva, Ted's, and Lacey. I ended up having to pull it off, and go back to a stock drive shaft.
  22. Replies
    21
    Views
    5,895

    Using a quality-accurate torque wrench is also...

    Using a quality-accurate torque wrench is also key here!
  23. Replies
    6
    Views
    814

    http://www.mcmaster.com/#stainless-steel-dowel-pin...

    http://www.mcmaster.com/#stainless-steel-dowel-pins/=12j9qkg
  24. Replies
    6
    Views
    814

    https://www.grainger.com/category/dowel-pins/pins/...

    https://www.grainger.com/category/dowel-pins/pins/fasteners/ecatalog/N-8m0?okey=stainless+dowel+pins&mkey=Dowel+Pins+&refineSearchString=stainless+dowel+pins&NLSCM=5&EndecaKeyword=stainless+dowel+pins...
  25. If my memory serves me correctly..... those...

    If my memory serves me correctly..... those threaded plate inserts were added to the 08+ models. Pre-08's the hose fittings screwed directly to the upper aluminum plate that's bolted to the ride...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4