Search

Type: Posts; User: TaulmanServices

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    4,016

    BTW look at my posts I bought an xlt 1200 2002 a...

    BTW look at my posts I bought an xlt 1200 2002 a pair of them and one had a lean condition and fried middle cylinder too and they were bone stock had to get new parts costs about 1500 per skis
  2. Replies
    13
    Views
    4,016

    I did the oside bill rejet with Riva flame...

    I did the oside bill rejet with Riva flame arrestor and adjusted throttle now when I try to accelerate the max the skis go in 30mph roughly do I need to adjust the pop off or highs and lows? I did...
  3. Also add that it has the Riva Flame Arrestors...

    Also add that it has the Riva Flame Arrestors with the water socks on
  4. 1200 XLT 1200 Good Compression, Good Spark, Good Fuel No Start?!

    Hi all. It has been awhile since I have posted on here but I was able to successfully rebuild both of my 2002 Yamaha XLT 1200s. I seek your help again. Any issue has arisen with the second Jetski I...
  5. Replies
    4
    Views
    1,160

    also which direction ares measured for the upper...

    also which direction ares measured for the upper and lower cylinder decks?
  6. Replies
    4
    Views
    1,160

    Yes but the factory manual shows getting the...

    Yes but the factory manual shows getting the taper and out of round measurements too by taking six measurements for the cylinder jugs

    and

    how does one know when the micrometer is flush on the...
  7. Thank you guys for the information- maybe you can...

    Thank you guys for the information- maybe you can help me on my measurement questions
    http://www.greenhulk.net/forums/showthread.php?t=241515

    I am so close to getting everything back together I...
  8. Replies
    4
    Views
    1,160

    How to take proper measurements

    Hey guys,
    I have some really important questions about the most important measurements one can take on any engine but in particular focusing on the 66v Yamaha Engine for my...
  9. Replies
    3
    Views
    556

    Check the voltage to the starter. Your starter...

    Check the voltage to the starter. Your starter could be going bad. The ground cables at the ends, check them for corrosion, check the starter terminals for corrosion (green copper oxidation)- if the...
  10. ok that first time- before starting it or while...

    ok that first time- before starting it or while it is running? My concern is that the rings will mar up the piston walls if it isn't very lubricated
  11. Ok thanks guys, only a few more questions- one of...

    Ok thanks guys, only a few more questions- one of the two 02 xlt 1200 skis has been sitting for awhile and was not taken apart- should i drop some ski craft oil down there (5ml) and maybe bump the...
  12. What are the indications that the Break in is not...

    What are the indications that the Break in is not going well?
  13. Thank you guys, ...

    Thank you guys,
    Bryon I am going to buy the following items off amazon:
    I am going to use the Yamalube and Ring Free Plus Fuel Additive on break in- if you have any...
  14. I kinda wanted to dry start it just to see if it...

    I kinda wanted to dry start it just to see if it will turn on
  15. Well Can I turn it on for a minute or two when...

    Well Can I turn it on for a minute or two when its on dry land or should I do a first start in the water? Will the fuel filter- filter out any of the 32:1 oil?
  16. I need to do the breakin in water correct? The...

    I need to do the breakin in water correct? The other option is I connect the water hose and while the engine is dry start it up where i am working on it in the garage? Also Since it is premix now...
  17. I FIGURED IT OUT!!!:smt119 Ok so here is some...

    I FIGURED IT OUT!!!:smt119

    Ok so here is some advice that I have not seen anyone write down in this forum so far. To anyone that attempts this with zero prior knowledge here is what I have learned...
  18. From reading the original tuning thread i am...

    From reading the original tuning thread i am going to strech the springs to get the 42-45 psi needed on the carbs. about the gaskets i am going to grease both sides with marine grease does this sound...
  19. Ok is it normal for the crank to pop off...

    Ok is it normal for the crank to pop off violently like that? I am assuming the woodruff key cannot break in two can it?
  20. Adam thank you for the responses. Check if the...

    Adam thank you for the responses. Check if the fuel pump gaskets are leaking- do this by watching the fuel pump gaskets?
    I got the winderosa gasket kit and they are a different material then the...
  21. Mukini SBNI 44 Carb POP OFF Issues Tuning 2002 XLT 1200

    Hey all I will post pictures of my setup but I am running into the following issues and I am unsure what do to. I have the carbs all tuned to Oside bills specs, 1.5n/s, 110 pilot, 120 main, drilled...
  22. I don't know its too dark out side here to look...

    I don't know its too dark out side here to look right now but in the morning I will: if I do need to get it this is the part I buy yes?...
  23. 2002 XLT 1200 And Yamaha Woodruff Key Replacement?

    Hello all
    I am getting closer and closer to finishing my XLT rebuild and will be posting the entire process soon. I have a question I took the flywheel off the crank with a...
  24. Ok what about the procedure?

    Ok what about the procedure?
  25. Replies
    11
    Views
    1,087

    I have a kinda silly question but in Florida we...

    I have a kinda silly question but in Florida we do not have much of a winter- I may always use them throughout the winter. After how long is it a go ahead to fog an engine- after two, three, or xx...
Results 1 to 25 of 128
Page 1 of 6 1 2 3 4