Search

Type: Posts; User: martincom

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. You'll find that piston fitment info here as well...

    You'll find that piston fitment info here as well as other relevant info.
  2. I'd suggest you measure the cylinder bore taper...

    I'd suggest you measure the cylinder bore taper and out-of-round. Often, I find cylinders can "look" good and hone up well. However, when I measure taper and out-of-round, they are worn well...
  3. Replies
    107
    Views
    2,785

    The engine will crank without the lanyard in...

    The engine will crank without the lanyard in place on a Virage i. That is normal.

    On a Virage i, the only items that are powered from the battery/12 volt section of the stator is the MFD,...
  4. Replies
    107
    Views
    2,785

    Correct, CPS is an acronym for Crank Position...

    Correct, CPS is an acronym for Crank Position Sensor.

    You'll find the answers for your other questions here.
  5. Replies
    5
    Views
    149

    There was another thread with near identical...

    There was another thread with near identical symptoms on a 2002 Genesis I. You may want to take a look at it or PM the OP and see if he resolved the issue.
  6. Replies
    5
    Views
    149

    I'd start by monitoring the fuel pressure, at the...

    I'd start by monitoring the fuel pressure, at the Schrader valve, in the return line. It should be a consistent 25 psi. You can obtain an affordable gauge here. You'll want to monitor it while it...
  7. Wow, been awhile since you've made an appearance....

    Wow, been awhile since you've made an appearance. Were you just paroled? :roll:
  8. Replies
    47
    Views
    1,818

    Now, that I'm "old", according to my daughters, I...

    Now, that I'm "old", according to my daughters, I have finally figured why people become such pack rats when they get older. You remember how much it cost when new...
  9. Replies
    47
    Views
    1,818

    I never sheared a woodruff key in a watercraft. ...

    I never sheared a woodruff key in a watercraft. I've only had it occur twice, both with my former Lawn Boy walk behind mower. On both instances, I hit something like a survey monument or some other...
  10. Replies
    47
    Views
    1,818

    Good call. An ounce of prevention is worth a...

    Good call. An ounce of prevention is worth a pound of cure.
  11. Replies
    47
    Views
    1,818

    I can't tell from the photo, is it just the...

    I can't tell from the photo, is it just the woodruff key that is sheered? If so, they're generic and the local hardware store probably has them. If it was sheered, it was probably from sudden...
  12. I'm going to speculate he is catholic and has an...

    I'm going to speculate he is catholic and has an "in" with the bishop, who splashes holy water on it once a week.
  13. Replies
    47
    Views
    1,818

    You should be able to remove the flywheel nut and...

    You should be able to remove the flywheel nut and washer and check if the woodruff key is in the flywheel keyway, with a flashlight. You may or may not be be able to determine if it has been sheered...
  14. I've never had anything to do with the carb skis,...

    I've never had anything to do with the carb skis, so I can't offer an opinion in regards to cross referencing.

    As far as resurrecting the Genesis DI, it would have to be a cosmetically good hull....
  15. Replies
    4
    Views
    273

    ...and here....

    ...and here.
  16. Replies
    4
    Views
    273

    Here is some more info. ...

    Here is some more info.
  17. Did you have the tether inserted? It, also, must...

    Did you have the tether inserted? It, also, must be inserted for the EMM to power up.
  18. I just re-read the thread. What was the outcome...

    I just re-read the thread. What was the outcome of the low, 3.7 volts, white/red power bus wire voltage reading? It sounded like you were on to the issue there. Based on your EMM checks and...
  19. Have you or can you connect a fuel pressure gauge...

    Have you or can you connect a fuel pressure gauge and monitor the fuel pressure when it hesitates/dies? It should be a consistent 25psi.
  20. To utilize Digital Wrench (DW) without the engine...

    To utilize Digital Wrench (DW) without the engine running, you must disconnect the EMM power board output plug and install a bypass plug or jumper across two pins of the plug (wiring harness...
  21. Don't forget to apply red Loctite to the...

    Don't forget to apply red Loctite to the crankshaft taper and the flywheel nut threads. As I noted in a previous post, I'd suggest you apply anti-seize to the starter nose piece to prevent this from...
  22. Replies
    4
    Views
    190

    Yes

    Yes
  23. WTB - Parts So I'm assuming you have resolved all the...

    So I'm assuming you have resolved all the mechanical issues?
  24. Replies
    4
    Views
    190

    Check the fuel pressure next. There should be a...

    Check the fuel pressure next. There should be a Schrader valve (tire stem in appearance) in the return fuel line. You should see 25 psi when cranking/running. You can obtain an affordable gauge...
  25. Replies
    11
    Views
    422

    I'd check the Crank Position Sensor next. You...

    I'd check the Crank Position Sensor next. You can check it with an ohm meter. I'd check it when it will start, again after it will not, and compare the two measurements. It will typically measure...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4