Search

Type: Posts; User: krispaintballz

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Hey guys whats going on? Still around and very...

    Hey guys whats going on? Still around and very much into skis but two kids now i need to free up some cash and get some new skis. Thinking an fzr and a vxr.
  2. Hi all!!!! Havent been on here in forever. Well...

    Hi all!!!! Havent been on here in forever. Well its time i am selling this ski. I have a lot of parts with it too! All of it goes. Too much to list and many of you know all the stuff i have. All...
  3. Replies
    5
    Views
    1,359

    they had a lifetime warranty on the gpr pipes but...

    they had a lifetime warranty on the gpr pipes but never on the 97-99 triples. Those were never mass produced and probably sold a small percentage compared to the gpr pipes. I have welded the gp pipes...
  4. The throttle cable is adjusted wrong. give it...

    The throttle cable is adjusted wrong. give it more slack in the cable by adjusting the 10mm nut by the throttle bracket. the tension on cable is holding it in the open postition and not allowing the...
  5. Replies
    11
    Views
    10,905

    I run wisecos. They run good for me. Remember its...

    I run wisecos. They run good for me. Remember its not the piston its the person setting up the ski for the piston. You have to make sure you run your clearances. I have no problems running them at...
  6. Replies
    10
    Views
    1,696

    You will be truly missed!!!! Go-karting in...

    You will be truly missed!!!!

    Go-karting in California
  7. Here is my setup

    Here is my setup
  8. I use them all the time with no troubles. If you...

    I use them all the time with no troubles. If you snapped off a terminal you torqued it down too much. I also run all two stroke skis total loss with no problems. I would NEVER EVER use a deka battery...
  9. Replies
    8
    Views
    3,655

    Fuck sbt. Just go with the quicksilver. ...

    Fuck sbt.

    Just go with the quicksilver.

    They make the best waterproof grease. It is called 2-4-c and is made by quicksilver.
  10. Replies
    8
    Views
    3,655

    Use a good 2 stroke castor oil for break in then...

    Use a good 2 stroke castor oil for break in then run a full synthetic.
  11. Sounds like you might have accidently used the...

    Sounds like you might have accidently used the whole can of fogging oil. Run it on the lake and get it cleaned out a bit. After about 20 mins you probably have it cleaned out i bet a lot of that...
  12. Heat gun works wonders!!!!!!!! Love it! My best...

    Heat gun works wonders!!!!!!!! Love it! My best friend on old skis. IMPORTANT: clean the plastic really good before baking or you will imbed it into the plastic.
  13. Replies
    7
    Views
    851

    I use clear and colored lines. Your not sucking...

    I use clear and colored lines. Your not sucking with vaccum power, it is a small pulse. Been using it for years no trouble. But if you are really anal go buy the oem stuff. I will buy the clear or...
  14. Replies
    5
    Views
    686

    Just call moto tassinari and let them know your...

    Just call moto tassinari and let them know your reeds were chipping prematurely and they will send you new ones free of charge.
  15. WTB - Parts Nut sack youll never find one. Blew up my...

    Nut sack youll never find one.

    Blew up my sled. Went out once doing 91 mph snapped a belt reved crazy and pow! Cracked pto cyl.
  16. Replies
    4
    Views
    518

    Then do what the manual said. I dont know why you...

    Then do what the manual said. I dont know why you ask forum members.
  17. Replies
    4
    Views
    518

    Put loctite on key and snout hammer on flywheel...

    Put loctite on key and snout hammer on flywheel with dead blow hammer. Then zip on the bolt with loctite and zip it back off put a drop more back on zip it on and torque it to 55 ft/lbs.
  18. Looks like a set off a polaris. Yami used mikuni.

    Looks like a set off a polaris. Yami used mikuni.
  19. Replies
    8
    Views
    1,079

    Unbolt and remove the rideplate, then locate and...

    Unbolt and remove the rideplate, then locate and unbolt the 2 bolts on top of the pump and the 4 long ones holding pump together. Finally locate the tabs on the side of the pump, put a flat head in...
  20. I prefer kloz. All oil is ok oil these days. Yes...

    I prefer kloz. All oil is ok oil these days. Yes some say my oil is better blah, blah, blah. Bottom line use what you like. Try different kinds. If klotz was not easy to get here i would probably use...
  21. Replies
    22
    Views
    4,163

    Any good epoxy based primer and poly paint will...

    Any good epoxy based primer and poly paint will work. Dont get too much into it. Hulls are selling for 100.00 around here.
  22. Replies
    22
    Views
    4,163

    Buy a used hull and transfer everything. You will...

    Buy a used hull and transfer everything. You will have more work, time, and money in the repaired hull than the replacement hull.
  23. Ttt

    Ttt
  24. FS - Parts pmed

    pmed
  25. Replies
    2
    Views
    1,207

    Run three off the head overboard and run 3 off...

    Run three off the head overboard and run 3 off the pipes overboard.

    You can also block three holes on the 6 way manifold and run three to the cyls out the head, then into the pipes, then...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4