Search

Type: Posts; User: Ryan-virage

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    159
    Views
    4,145

    hey fellas just to clarify i do have a very weak...

    hey fellas just to clarify i do have a very weak spark on my PTO side and NO spark at all on the MAG side. the PTO spark is very weak i can barely see it sparking when holding it to the cylinder...
  2. Replies
    159
    Views
    4,145

    Ok I’ll go in depth on the wiring next chance I...

    Ok I’ll go in depth on the wiring next chance I get.. any chance the capacitor could have anything to do with this?
  3. Replies
    159
    Views
    4,145

    Hey guys so I just got the news today from...

    Hey guys so I just got the news today from lakeside that my EMM tested out good. Not to sure if I’m happy or not lol that still leaves me with weak spark on one cylinder and nothing on the other... I...
  4. Replies
    159
    Views
    4,145

    Ok I got er labeled I took pictures and I got it...

    Ok I got er labeled I took pictures and I got it in a box of bubble wrap within a box of bubble wrap lol should be good to go I hope!
  5. Replies
    159
    Views
    4,145

    found it in a google search lol i guess ill leave...

    found it in a google search lol i guess ill leave this to the professionals, my first choice is lake side for sure. ill be contacting him as soon as expenses let me ;) i cant give up on er now lol
  6. Replies
    159
    Views
    4,145

    just wondering if there is any truth to the...

    just wondering if there is any truth to the information on this board? if so i would assume the components i need changed are the SCR's and the voltage regulator? and after reading thro the forum i...
  7. Replies
    159
    Views
    4,145

    Ok will update that for sure.. wish there was...

    Ok will update that for sure.. wish there was another emm I could test around here it’s almost 700$ Canadian to have the emm repaired so I may just part it out at this point can’t decide...also...
  8. Replies
    159
    Views
    4,145

    Ok I did check the voltage while everything was...

    Ok I did check the voltage while everything was hooked up and have the 25 vdc so I’ll start saving my pennies to ship off the emm to lakeside tech! One question what kind of screw is in the 40 pin...
  9. Replies
    159
    Views
    4,145

    I get a 25v while cranking at the red/white wire...

    I get a 25v while cranking at the red/white wire at the injectors... the coil checked out good .275 on both primary’s... just kinda lost I’m guessing that just leaves the EMM thyristor??? I think...
  10. Replies
    159
    Views
    4,145

    Hey guys so yesterday I got a new plug wire and...

    Hey guys so yesterday I got a new plug wire and put on and all is well there, but I still having a extremely weak spark.... did some reading on the manual and it looks like the next step may be...
  11. Replies
    159
    Views
    4,145

    Well it’s all thanks to you guys haha but I’m...

    Well it’s all thanks to you guys haha but I’m learning a lot and I appreciate all the knowledge you guys share.
  12. Replies
    159
    Views
    4,145

    Tried some different plugs with no changes I...

    Tried some different plugs with no changes I pulled my plug wires off and did a ohms test on both. One was fine and the shorter one if you move it one way or another I got a OL reading so safe to say...
  13. Replies
    159
    Views
    4,145

    Ok I’m doing my best to understand here I’m still...

    Ok I’m doing my best to understand here I’m still learning as I go... so I had spark in the PTO and nothing on the MAG side. I swapped the primary connections and had no differences. I decided to go...
  14. Replies
    159
    Views
    4,145

    I just trued swapping the orange and green for...

    I just trued swapping the orange and green for the orange and blue and have no difference still sparking on one side and not the other... ohms stay about the same
  15. Replies
    159
    Views
    4,145

    Ohms mode

    Ohms mode
  16. Replies
    159
    Views
    4,145

    Service manual says 0.05-0.15 for primary’s. I...

    Service manual says 0.05-0.15 for primary’s. I read .267 on both coils.
    service manual says 225-325 on secondary’s. I read .575 and .654 on the secondary’s.
  17. Replies
    159
    Views
    4,145

    Ok so I held my probes together and it zeroed out...

    Ok so I held my probes together and it zeroed out every time, I went from the batty negative to the head of the machine and it zeroed, I double checked my readings and I’m confident the resistances...
  18. Replies
    159
    Views
    4,145

    Ok thanks so much, so from what I gather the...

    Ok thanks so much, so from what I gather the resistances are all high? Does that point to a faulty coil?
  19. Replies
    159
    Views
    4,145

    plug wires i meant to say sorry for the confusion...

    plug wires i meant to say sorry for the confusion im using a innova 3320 meter and thanks for the tip.
  20. Replies
    159
    Views
    4,145

    thanks man lol id be lost without you...:) so i...

    thanks man lol id be lost without you...:) so i did some homework to make sure im testing this right and im confident i got the results i checked them about 3 times... so in the manual the primary...
  21. Replies
    159
    Views
    4,145

    Ok so I found the specs in the manual.. just have...

    Ok so I found the specs in the manual.. just have one question and I can’t find it in the manual.. how do I tell which post is my primary and which is secondary?
  22. Replies
    159
    Views
    4,145

    So I pulled the coil this morning and cleaned up...

    So I pulled the coil this morning and cleaned up the grounding straps and bolts. Scratched the metal mounting plate as well. While it was out I did a ohms test between primary and the grounding...
  23. Replies
    159
    Views
    4,145

    Ok I’ll take the coil off see if I can clean up...

    Ok I’ll take the coil off see if I can clean up the bolts and that thin piece of metal. I removed the plugs from the coil and noticed some white corrosion on one post. Is there anyway of actually...
  24. Replies
    159
    Views
    4,145

    Ok thanks for the reply I appreciate all the...

    Ok thanks for the reply I appreciate all the help. I measured the resistance in the CPS which was 140.2. TPS red wire throttle open and shut was 5.27 green wire measured .71 closed and wide open 4v....
  25. Replies
    159
    Views
    4,145

    Ok I apologize if I’m being confusing and...

    Ok I apologize if I’m being confusing and annoying i must have read some wrong information about the TPS I’ll try and follow the methods you guys give me. Not to sure where to go from here obviously...
Results 1 to 25 of 81
Page 1 of 4 1 2 3 4