Search

Type: Posts; User: 2Blown98

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. No worries. Also to your point, each time I’ve...

    No worries. Also to your point, each time I’ve had these apart and used the driveshaft to turn over the motor in the method above I have had the PTO removed and obviously the supercharger as well.
  2. I don’t Believe any factory tool like the one...

    I don’t Believe any factory tool like the one you’re describing exists. However, it’s not necessary. With the plugs removed, you can insert the driveshaft and the motor should spin by hand pretty...
  3. Replies
    12
    Views
    356

    No social media for me. Thank you though!

    No social media for me. Thank you though!
  4. Replies
    12
    Views
    356

    my email keeps getting kicked back as...

    my email keeps getting kicked back as undeliverable http://greenhulk.net/forums/blob:http://greenhulk.net/25c45b7a-5fab-4f29-bb19-2b5dc113e505
  5. Replies
    12
    Views
    356

    Trying to PM you but you’re unable to receive...

    Trying to PM you but you’re unable to receive them.
  6. Replies
    12
    Views
    356

    This may be the explanation as I found no signs...

    This may be the explanation as I found no signs of contamination on the spark plug washers.
    JM219, pm inbound
  7. Replies
    12
    Views
    356

    View Post

    So I had my machine out yesterday for a couple hours and I noticed I was experiencing a weird condition after fairly extended top speed runs. My number one cylinder coil would pop off just enough to...
  8. Yes

    Yes
  9. Replies
    14
    Views
    1,087

    I would be shocked if the insurance company would...

    I would be shocked if the insurance company would even attempt to have a shop fix a hole in the hull. It’s a huge liability on their part. However, we’re in interesting times. I would express to them...
  10. Replies
    14
    Views
    1,087

    I wouldn’t want it back…

    I wouldn’t want it back…
  11. Replies
    7
    Views
    525

    Update: ptscon, you were correct. Works terrific...

    Update: ptscon, you were correct. Works terrific now!
  12. Replies
    2
    Views
    448

    Tough to say because of the bluish light from the...

    Tough to say because of the bluish light from the flash. However I’d be concerned about any real noticeable dust with such low hours
  13. Replies
    2
    Views
    253

    You only got water half way up the supercharger...

    You only got water half way up the supercharger so it’s not the end of the world. Off the top of my head, the only electrical connections that low are the egt sensor in the water box and the oil...
  14. Replies
    7
    Views
    525

    It’s currently installed on a 2012 GTR. I used an...

    It’s currently installed on a 2012 GTR. I used an exhaust spacer also. Had to do a little grinding on the valve cover as well as the top of the cylinder head so that I could
    install and remove the...
  15. Replies
    7
    Views
    525

    Thank you, that’s a good explanation of what is...

    Thank you, that’s a good explanation of what is probably happening. I’m a little dense when it comes to these things. I’ll check it out this weekend and report back. Thanks for your help
  16. Replies
    7
    Views
    525

    Just the normal dashpac website

    Just the normal dashpac website
  17. Replies
    7
    Views
    525

    View Post

    Just got my new ultimate dashpac installed a few weeks ago and have only had a chance to get the ski in the water twice. Product works well as expected but I can’t for the life of me figure out the...
  18. Any o-ring will do, however I would either...

    Any o-ring will do, however I would either loc-tite it on or better yet run the factory rubber cone
  19. These aren’t like the newer superchargers. Both...

    These aren’t like the newer superchargers. Both nuts must be torqued to a fixed value. I believe off hand it’s 22lbft and 24lbft respectively. To change the slip moment change the spring washer...
  20. It should come out relatively easily. Just twist...

    It should come out relatively easily. Just twist back and forth.
  21. I’d buy it for the right price only if you’re...

    I’d buy it for the right price only if you’re comfortable building a motor if it’s a worst case scenario
  22. Replies
    2
    Views
    322

    WTB - Parts WTB Alignment tool

    Good afternoon and happy Father’s Day to all. I am looking to buy or rent an alignment tool ASAP. I am in the Jersey shore area
  23. Have you checked the pump seal?

    Have you checked the pump seal?
  24. ����

    ����
  25. You are of course correct. Good catch!

    You are of course correct. Good catch!
Results 1 to 25 of 153
Page 1 of 7 1 2 3 4