Search

Type: Posts; User: Mockingee

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    11
    Views
    245

    Will a bad TPS cause a no spark condition? What...

    Will a bad TPS cause a no spark condition? What does it do with the TPS unplugged?
  2. Replies
    27
    Views
    521

    Hmm, my ignorance is showing once again. I...

    Hmm, my ignorance is showing once again. I thought that was done in the MFD.
  3. Replies
    27
    Views
    521

    This is all really cool and interesting. Before I...

    This is all really cool and interesting. Before I say more let me point out that I only have experience with my Genesis so my question might be a stupid one. Perhaps things are different on other...
  4. Replies
    11
    Views
    245

    Have you tried testing the fuel pressure on the...

    Have you tried testing the fuel pressure on the water as it’s acting up? Have you done the fuel pressure regulator reinforcement?
  5. Replies
    57
    Views
    1,445

    Jealous.

    Jealous.
  6. Replies
    50
    Views
    2,389

    If I were you, having already shelled out the $...

    If I were you, having already shelled out the $ for that sensor, I would either try to adapt it to the other end of the throttle shaft or offset it on the correct end of the throttle body and make a...
  7. Replies
    15
    Views
    546

    Wow, I had no idea this is so simple. I thought...

    Wow, I had no idea this is so simple. I thought there was precision machining involved. Maybe next time I rebuild my 1200, (hopefully many yrs down the road), I’ll give it a try.
  8. Replies
    47
    Views
    7,288

    Check to see if you can turn the engine by hand...

    Check to see if you can turn the engine by hand by grasping the drive coupler. With the spark plugs out it should turn freely.
  9. Replies
    50
    Views
    2,389

    After looking further it seems that sensor is...

    After looking further it seems that sensor is obsolete. Maybe this one could be made to work. This seems to be available for about $70. Voltages are slightly off but maybe close enough?

    Honeywell...
  10. Replies
    50
    Views
    2,389

    It looks to me as if Honeywell RPNS090AC1A21X...

    It looks to me as if Honeywell RPNS090AC1A21X could be adapted. It’s definitely not a drop in replacement part. I’m not sure if the housing would stand up or what the cost would be.
    ...
  11. Replies
    8
    Views
    283

    I’m no expert but that doesn’t look like lean...

    I’m no expert but that doesn’t look like lean burn to me. It looks as if something went though it. I would look very closely at the bottom rod bearing and crank bearings in that cylinder.
  12. Good, you’re ahead of the game on the fpr. Odd...

    Good, you’re ahead of the game on the fpr. Odd that it won’t rev. My Genesis does 5000 rpm with hardly any throttle. Does it feel as if it’s pulling hard or just feel as it would if you were to just...
  13. You should check compression in all three...

    You should check compression in all three cylinders and above all, do the fuel pressure regulator reinforcement.
  14. Replies
    50
    Views
    2,389

    I can’t find anything on Honeywell’s website that...

    I can’t find anything on Honeywell’s website that mentions this sensor being available in anything other than cw rotation. Granted I’m no expert so maybe I’m just overlooking it.
  15. Replies
    50
    Views
    2,389

    On the website it says high voltage cw and low...

    On the website it says high voltage cw and low voltage ccw. I’ll have to go look at mine but is that the wrong way for us?

    According to K447’s post above it seems so.
  16. Replies
    4
    Views
    206

    Even though your Genesis is 20 yrs old it’s a...

    Even though your Genesis is 20 yrs old it’s a unique machine. I recently spent a bunch of $ on mine rather than buy another ski because it is perfect for my family. It’s 4 person designation means I...
  17. Replies
    10
    Views
    385

    If it sat a long time and runs good without the...

    If it sat a long time and runs good without the exhaust hooked up is it possible some rodent built a nest in the exhaust?
  18. Replies
    14
    Views
    1,491

    This is no help to you but just a comment. ...

    This is no help to you but just a comment.

    I’ve read posts similar to this before and I find it totally amazing that these engines can run at those high RPM’s with the throttle plates closed and...
  19. Replies
    12
    Views
    276

    SBT will rebuild your cylinders if the aluminum...

    SBT will rebuild your cylinders if the aluminum is OK and supply new pistons and gaskets for a reasonable, up front price. Many people seem to be of the opinion that SBT parts are junk. I don’t have...
  20. Replies
    13
    Views
    350

    Yep, that sucks. The bottom bearing on that rod...

    Yep, that sucks. The bottom bearing on that rod got moisture in it, rusted and seized at whatever RPM you were running at the time. It’s a safe bet you’re right and more bearings on the crank are bad...
  21. Perfect, not a hitch. Rebuilt the motor over the...

    Perfect, not a hitch. Rebuilt the motor over the winter but that was unrelated.
  22. View Post

    I hope itís OK if it bleeds down because my Genesis does, and has as long as Iíve had it.
  23. Replies
    29
    Views
    461

    I was also nervous about tapping the brittle...

    I was also nervous about tapping the brittle plastic but it turned out to be fairly easy.

    I have never had the FPR fall out but I would think that if it were easy to notice there wouldn’t be so...
  24. Replies
    13
    Views
    350

    If I were you I would do a complete engine tear...

    If I were you I would do a complete engine tear down. That’s rust in that cylinder caused by moisture getting in there while it sat for those four years. If there’s rust in the cylinder there is very...
  25. Replies
    4
    Views
    171

    I think it’s better to have your EMM repaired...

    I think it’s better to have your EMM repaired than buying another. Firstly, if u put in a different EMM you need to have the matching injectors in the original order, or have the replacement EMM...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4