Search

Type: Posts; User: DanSVHO

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    36
    Views
    1,905

    that’s what I need to do next. I’m debating...

    that’s what I need to do next. I’m debating wether to add to side cowling of front storage compartment like the unlimited intake from GH store.
  2. Replies
    36
    Views
    1,905

    deans extended one I don’t know the size

    deans extended one I don’t know the size
  3. Replies
    36
    Views
    1,905

    im going to try no wedge later. That new plate...

    im going to try no wedge later. That new plate maybe the ticket.
  4. Replies
    36
    Views
    1,905

    No wedge. stock wheel? Stock fueling? Any...

    No wedge. stock wheel? Stock fueling? Any proposing at those speeds?
  5. Replies
    36
    Views
    1,905

    what mods do you have?

    what mods do you have?
  6. Replies
    36
    Views
    1,905

    both intake and exhaust

    both intake and exhaust
  7. Replies
    36
    Views
    1,905

    if I Shimming the front of plate, the plate will...

    if I Shimming the front of plate, the plate will be lower than the grate though. I had shims in rear of plate. I removed them but started bouncing more. My speed today was down a lot only hit 85.5 at...
  8. Replies
    36
    Views
    1,905

    Cool. You have his new extended ride plate? Let...

    Cool. You have his new extended ride plate? Let me know how it is I might be getting that soon. you shim the front of the ride plate close to the grate?
  9. Replies
    36
    Views
    1,905

    I’ve been running a pump which since I bought the...

    I’ve been running a pump which since I bought the ski but I’ve been hearing that it actually hurts it top end and creates porpoising. So, I might take it out and see what I run without it.
  10. get yourself a deans plate and a pump wedge.

    get yourself a deans plate and a pump wedge.
  11. Replies
    36
    Views
    1,905

    thanks. Yea a lot or testing and tweaking. Still...

    thanks. Yea a lot or testing and tweaking. Still not completely done, I’m doing the grate mod now and will mess with shims on ride plate.
  12. Meant to say tuning. Yea you can run a tune based...

    Meant to say tuning. Yea you can run a tune based on What mods you have. But you will not Unlock or get the most out of it without the supporting mods.
  13. Replies
    36
    Views
    1,905

    its not that’s Different actually. It’s more of a...

    its not that’s Different actually. It’s more of a slight surge of idle then it catches itself and repeats. Very suddle though.
  14. Replies
    36
    Views
    1,905

    well, the taller prop and high rpm helps with...

    well, the taller prop and high rpm helps with overstuff. Getting that water out as fast as possible. I believe it’s only 3mm smaller.
  15. Replies
    36
    Views
    1,905

    this is with a deans reduction and extended...

    this is with a deans reduction and extended nozzle. I don’t know that actual diameter. And the prop is pitched to about a 13/17 to keep the rpms higher. This is with no kaneflex mated to the intake...
  16. Not necessarily. What’s your wanting in...

    Not necessarily. What’s your wanting in considered very mild and reliable. The bolt ons that compliment the tune will allow for the most speed and Consistent power. The Ruben changes several things...
  17. There are plenty of bolt ons but you still need...

    There are plenty of bolt ons but you still need the raise the rev limiter to increase speed. If you don’t, even with some simple bolts ons you will be on the limiter and be slower. To make the beat...
  18. Replies
    36
    Views
    1,905

    Max rpms read-9230- 21 lbs of boost. And...

    Max rpms read-9230- 21 lbs of boost. And porpoising a little. I think with some tweaks to prop and going rpm to 9400. And possible cutting center bar out of intake grate. Could go even more.
  19. Replies
    36
    Views
    1,905

    Cancel

    Cancel
  20. Replies
    36
    Views
    1,905

    yea it should be an animal coupled with the new...

    yea it should be an animal coupled with the new et wheel. Soon as my spring comes in I’ll retest.
  21. Replies
    36
    Views
    1,905

    Et20 + vxr cams 2019 FX

    Just finished installed the new wheel and cams. I also did deans Venturi nozzle upgrade along with a taller pitch. It loads the pump better because it’s a smaller exit size) I tested on Saturday but...
  22. Replies
    7
    Views
    288

    Shoot for 11.9-12 wot

    Shoot for 11.9-12 wot
  23. Replies
    0
    Views
    85

    Tq specs for Ride control motor.

    What are the tq specs for the ride motor control motor? At back for ski?
  24. Replies
    27
    Views
    961

    ok. I’m just going to use the 4200 then and ax...

    ok. I’m just going to use the 4200 then and ax the blob of epoxy at the center. Only thing I found that would work is west systems 510 epoxy in a caulking application.
  25. Replies
    27
    Views
    961

    So don’t add the gob of the hard epoxy on the...

    So don’t add the gob of the hard epoxy on the center of bracket? Just the 4200? Would 5200 be a stronger bond?? I’d rather use that if so. Also the stuff that’s left of the hard epoxy is part of the...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4