Search

Page 1 of 16 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    15
    Views
    323

    My guess is that the connector is made by...

    My guess is that the connector is made by Sumitomo (MT090-4)

    http://www.cycleterminal.com/mt-series-090.html

    http://www.cycleterminal.com/Sumitomo-MT-090-4-M(6188-0004)-F(6180-4771).jpg
  2. Your not going to get any more top end speed...

    Your not going to get any more top end speed until you reflash the ECU to remove the speed limiter, and then you will want the Solas 13/20

    https://www.4-tecperformance.com/images/F144792719.jpg...
  3. K447, you are pretty much on the money with your...

    K447, you are pretty much on the money with your assumptions on how it works :) people struggle to get their head around the idea of how I have things set up thinking it should be done differently,...
  4. Replies
    55
    Views
    4,324

    The prop Waterforfire posted a couple pages...

    The prop Waterforfire posted a couple pages before in this post has been on my 2018 RXTX since new. It was Waterforfire's idea to do a prop--15-22--and send it to Dave to fit by boat. The...
  5. Replies
    38
    Views
    1,595

    Please clarify your comments above . . . I'm...

    Please clarify your comments above . . . I'm assuming you are not referencing greasing via the Zerk fitting, and rather referencing the back of the IB housing, aka the void area that mates with the...
  6. Replies
    40
    Views
    3,996

    Carabiners are weak, even stainless steel ones. ...

    Carabiners are weak, even stainless steel ones.

    Use a snap shackle.
  7. Reverse would be indicated on the display. So it...

    Reverse would be indicated on the display. So it seems more likely that your TPS has an intermittent. Sometimes the problem is in the TPS wires vs the TPS itself (the wires can be repaired, I can...
  8. Replies
    16
    Views
    453

    Here is a link to the stator tests. ...

    Here is a link to the stator tests.

    http://greenhulk.net/forums/showthread.php?t=137006&p=1532376&viewfull=1#post1532376
  9. Buy RADIAL tires. They don't get as hot and hold...

    Buy RADIAL tires. They don't get as hot and hold up so much longer. Also, rotate the tires every year. A spare that doesn't get used will go bad.

    Keep the bearings greased, too!
  10. you should really go out and ride the ski for...

    you should really go out and ride the ski for awhile before doing mods. IMHO do a maptuner-x first and see how you like it.
  11. Replies
    10
    Views
    503

    The intake manifold on the NA motor is completely...

    The intake manifold on the NA motor is completely different than on the SVHO. I dont think the same applies as far as middle cylinders being leaner. The stock airbox is a lot more restrictive...
  12. Replies
    3
    Views
    195

    View Post

    If you’re leaking fuel near the rear of the engine, you either have a broken fuel rail, bad fuel line quick-connector, leaking injector o-ring, or possibly an issue with your fuel pressure regulator...
  13. Replies
    16
    Views
    718

    That's not the back seat! One more pointer to...

    That's not the back seat!

    One more pointer to glean from the pic: get the right ball mount... trailer should be towed level.
  14. My first guess would be you have contaminated...

    My first guess would be you have contaminated fuel and the the intake screen to the fuel pump is restricted/clogged. See this thread.

    Normally, this would be somewhat simple to check by a fuel...
  15. I'd probably go a different route. I always like...

    I'd probably go a different route. I always like to avoid modifications that prevent component swap outs or can consume an incredible amount of time of a future service by someone who is unaware of...
  16. Sticky: I just wanted to alleviate some of the paranoia...

    I just wanted to alleviate some of the paranoia about "blowing seals". Sure, as a general rule, please slow-down and go-easy when back-pressure builds in the grease gun - its a good indicator the IB...
  17. Replies
    21
    Views
    1,532

    Congrats on the new ski. Your ski isn't going any...

    Congrats on the new ski. Your ski isn't going any faster until you reflash the ECU to remove the speed limiter. With the MaptunerX, you can reflash it with the bone stock tune which removes the...
  18. Replies
    19
    Views
    2,175

    Understood and no the tongue is maybe 1/8 inch...

    Understood and no the tongue is maybe 1/8 inch higher than the tail on level ground with me and all my gear in the car. Not as big of a deal towing light weight like this as it would be if this was a...
  19. Replies
    2
    Views
    116

    Just a simple thanks

    First post. Awesome site, thanks for everything! Helped a ton troubleshooting my Virage.

    Have a 2002 Virage 800 DI that has been sitting for 3-4 years. Had trouble randomly dying before it was...
  20. Replies
    129
    Views
    4,152

    I stopped at my warehouse this morning and picked...

    I stopped at my warehouse this morning and picked up a nylon head piece. I also stopped at the hardware store and purchased some additional hose barbs. I have tapped the head piece and installed...
  21. Replies
    13
    Views
    625

    In almost 30 years as a first-responder...

    In almost 30 years as a first-responder (including time spent at Ground Zero and working in an area that was devastated by Superstorm Sandy), I've never seen anything like this. Hospitals have beds...
  22. Sticky: Thanks for the write up. Going to do this project...

    Thanks for the write up. Going to do this project on my 2016 fx svho. I think I found a better fitting if going the threaded hose route. Alemite 310912.
    ...
  23. Replies
    20
    Views
    1,019

    Greetings, HiPerCo mentioned you had a...

    Greetings,
    HiPerCo mentioned you had a driveshaft stuck in the bearing... I know this problem well. Down here in Florida I’ve had some that were so stuck from the saltwater you could have sworn it...
  24. Replies
    7
    Views
    483

    It's pretty common for folks to install a...

    It's pretty common for folks to install a dedicated pisser on the EMM exit water line. Then you can visually verify water flow.
  25. I think he gas tank is 15.5 gallons. But if you...

    I think he gas tank is 15.5 gallons. But if you are pre mixing I would mix the fuel in a container and add it to the tank so you always get a consistent mix ratio.

    I would not change any Polaris...
Results 1 to 25 of 400
Page 1 of 16 1 2 3 4