Search

Type: Posts; User: Jaugi

Search: Search took 0.00 seconds; generated 35 minute(s) ago.

  1. Replies
    2
    Views
    99

    Yep, that was pretty much my only thought since...

    Yep, that was pretty much my only thought since the intermediate shaft seems like it didnít brake or anything. Thanks!
  2. Replies
    2
    Views
    99

    PTO Coupler separated while riding?

    Hi,

    I have a gp1300r and I was out riding the other day cruising at about 50, when suddenly I lost all power. The motor still runs and revs normally, but it doesnít move. I was looking inside and...
  3. Replies
    6
    Views
    322

    Thanks, I just rebuilt the carbs again and I’m...

    Thanks, I just rebuilt the carbs again and I’m going to try this stuff again. How long do you wait between adjustments? and yes it isn’t cavitation. The jet ski doesn’t rev up right away
  4. Replies
    6
    Views
    322

    I’ve fiddled with the low speed jets for...

    I’ve fiddled with the low speed jets for countless hours, I can’t seem to get it right. Can’t tell if it’s too lean or too rich
  5. Replies
    6
    Views
    322

    View Post

    yeah, I followed the recipe. Iíll try that out, thanks!
  6. Replies
    6
    Views
    322

    Gp1200r hesitation

    Hey all,

    ive read up on some of the possible causes for the symptoms Im having but wanted to see if there is an order that I should check these things before starting. The ski was just rebuilt and...
  7. Thanks that’s what I am working on now. I still...

    Thanks that’s what I am working on now. I still want to do a leak down test on the crankcase too
  8. took the jetski out today, it started right up...

    took the jetski out today, it started right up and hit 52 top speed with no choke. If I gave it 1/4 choke it would get up to 56mph. With the modifications that I did, what should I be getting? I also...
  9. Today I think I may have fixed a big part of the...

    Today I think I may have fixed a big part of the problem but tomorrow I will bay test it in this 35 degree weather to make sure. �� I took out the fuel sender to remove the flap, which I did, and it...
  10. I rebuilt the carbs with mikuni carb kits. I...

    I rebuilt the carbs with mikuni carb kits. I still haven’t gotten the chance to do the leak down test because I didn’t realize the engine needed to be pulled again. I will do that but I haven’t had...
  11. Wow. Well here is part of the problem and I hope...

    Wow. Well here is part of the problem and I hope it didn’t cause any bigger problems. I pulled the plugs again to put a tester on the cylinders, 2 plugs say br8es-11 and 1 plug says br8es. I ordered...
  12. I just got my leak down tester in the mail about...

    I just got my leak down tester in the mail about 5 minutes ago. I will do the test and keep you posted. It seems like itís only hard to start the first time of the day but I need to add premix to the...
  13. it is a 2000 gp1200r

    it is a 2000 gp1200r
  14. Hard start, choke, accel pump removed, drilled return

    Hi guys,

    I did the aftermarket f/aís, removed accel pump, rejetted, did drilled return. I did it based on osidebills write up. The engine is still hard to start but once itís running itís good....
  15. Replies
    7
    Views
    382

    Thanks! I got rid of the accelerator pump, added...

    Thanks! I got rid of the accelerator pump, added flame arresters and rejetted. I did the 95 gram springs and 1.5 n&s. The thing fired up immediately and didnít bog anymore. Need a warm day for a...
  16. Replies
    1
    Views
    219

    I found one but I don’t know how to delete the...

    I found one but I don’t know how to delete the post. I just wanted to let everyone know because I don’t need one anymore
  17. Replies
    1
    Views
    219

    2000 GP 1200r idle adjustment cable

    Hi,
    I'm looking for an idle adjustment cable/springs/orings etc for my 2000 gp1200r. I tried to adjust it the other day and it snapped off. I believe the part number is 66V-14124-00-00
  18. Replies
    7
    Views
    382

    I decided I’m going to do the accel pump delete,...

    I decided I’m going to do the accel pump delete, rejet, add f/a’s according to osidebill’s procedure. I am also going to do the drilled return mod. Before putting the carbs in I will check pop off,...
  19. Replies
    7
    Views
    382

    View Post

    Thanks Iím going to keep looking into this over the weekend. I used the mikuni rebuild kits for all 3 carbs and I used the original springs. I never measured pop off which was a novice mistake but...
  20. Replies
    7
    Views
    382

    Hey thanks for the reply. I did not do the...

    Hey thanks for the reply. I did not do the drilled return mod. It looks pretty straight forward but I’m new to PWCs in general and wanted the opinions of experienced people before doing anything. Do...
  21. Replies
    7
    Views
    382

    Bogging 2000 gp1200r

    Hey guys,
    New to the forum. Iíve been looking through the forum and it seems like there is a ton of information on the problem Iím having but it also seems like it could be a few things. I bought...
Results 1 to 21 of 21