Search

Type: Posts; User: jetplane

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    359

    I have gauge for that unit for sale. It is...

    I have gauge for that unit for sale. It is perfect like bra d new.
  2. Replies
    8
    Views
    748

    Rxt-x 260 my 2010.

    Rxt-x 260 my 2010.
  3. Replies
    8
    Views
    748

    Here I am. I am going with 135+4 rapid cam solas...

    Here I am. I am going with 135+4 rapid cam solas 161mm 12.5/15 with lucky cone. 136 km/h @ 9000 rpm.
  4. Replies
    35
    Views
    2,127

    I don't understand how can be possible since if...

    I don't understand how can be possible since if you install the Regulator block off tap you don't touch the fuel hoses inside the pump. They are also quite difficult to move from the connector....
  5. Replies
    35
    Views
    2,127

    Very strange. If you have a leak you should...

    Very strange. If you have a leak you should notice some gasoline smell inside the hull and should be considerably strong.
  6. Replies
    35
    Views
    2,127

    What was the problem mate? I have exacly the same...

    What was the problem mate? I have exacly the same symptoms on mime. Why do you replace all the hoses if they were ok with no leaks?
  7. Normally on the 300 engines with the new SXX you...

    Normally on the 300 engines with the new SXX you should use 13/16 . 13/18 is too long .
  8. Replies
    6
    Views
    371

    it is also important to change the internal...

    it is also important to change the internal filter flow inside the pump .
  9. Hello guys any update on this?

    Hello guys any update on this?
  10. I'm curios to know what are the mods on this...

    I'm curios to know what are the mods on this monster !!!!!
    It is possible to have any info ?

    Thank you and best regards ,,
  11. Thread: pulley 300lx

    by jetplane
    Replies
    9
    Views
    658

    =D>Right !

    =D>Right !
  12. Thread: pulley 300lx

    by jetplane
    Replies
    9
    Views
    658

    You'll do this when you want to spin your...

    You'll do this when you want to spin your supercharger to higher rpm , since it has a lot of inertial wheight to prevent slippage of the belt .
  13. Replies
    91
    Views
    8,134

    Perfect another plus compared with old data...

    Perfect another plus compared with old data logger ! No battery drain when the engine is off ! Thank you Scott for the great news !
    Very strange to don't see advertizing of a useful tool like this ,...
  14. Replies
    91
    Views
    8,134

    this is a great tool ! Much better than the...

    this is a great tool ! Much better than the previous datalogger that was not absolutely waterproof and full of wirings and this new one give also the possibility to send the afr signal to the cluster...
  15. Replies
    91
    Views
    8,134

    Where did you buy it?

    Where did you buy it?
  16. Replies
    91
    Views
    8,134

    Ho does it cost ?

    Ho does it cost ?
  17. Sticky: You can buy also the individual parts . Normally...

    You can buy also the individual parts . Normally the things that need to be change are bearings , clutch washers and spring washers . You can save a lot of money .



    ...
  18. Sticky: I super agree with you. Dear all remember that...

    I super agree with you. Dear all remember that you can rebuilt your 300 supercharger with new parts whenever you want without balancing it since the only thing you have to be balanced is the wheel!...
  19. Replies
    8
    Views
    837

    Yes it is. If you are looking it I have a 029...

    Yes it is. If you are looking it I have a 029 lightened cam.
  20. Replies
    8
    Views
    837

    The main problem is the plasma coating on the 300...

    The main problem is the plasma coating on the 300 platform.
  21. Replies
    251
    Views
    40,672

    Thank you my Friend! I love Sicily, too! My...

    Thank you my Friend! I love Sicily, too! My favorite region!
  22. Replies
    251
    Views
    40,672

    I understand! Aniway I agree with you with the et...

    I understand! Aniway I agree with you with the et quality is one of the best choice you can do!
  23. Replies
    251
    Views
    40,672

    In Italy we produce many of your Rotax engine...

    In Italy we produce many of your Rotax engine components and we send to Austria. Just for the example in here we produce the 90 % of the components of the uropean racing and oem brand. Remember that...
  24. Replies
    251
    Views
    40,672

    Sorry mine is 135+4 , it is not an Et since most...

    Sorry mine is 135+4 , it is not an Et since most of the time et wheels produce some strange vibration I decided to have custom wheel produced by a friend o mine here in Italy , that have a better...
  25. Replies
    5
    Views
    667

    Yes correct !

    Yes correct !
Results 1 to 25 of 108
Page 1 of 5 1 2 3 4