Search

Search: Search took 1.00 seconds.

  1. Replies
    25
    Views
    1,251

    Very clean install. Did you ground the wire to...

    Very clean install. Did you ground the wire to the gauge or to the ecu? I assume since the wire runs direct to the ecu you would drop the wire from the ecu to ground but lets confirm it.

    Sean
  2. Replies
    25
    Views
    1,251

    No problem. Slo mode is disabled by grounding...

    No problem.
    Slo mode is disabled by grounding the blue/yellow wire as someone else said

    The non linear sensor is a pain as all gauges expect a linear resistance from full to empty.
    I can't find...
  3. Replies
    25
    Views
    1,251

    Sean, I fitted a replacement gauge to my 05 stx a...

    Sean, I fitted a replacement gauge to my 05 stx a couple of years ago when the clocks went kaput.
    I got one of these:...
  4. Replies
    25
    Views
    1,251

    Ip66 not rated for submersion but rated for water...

    Ip66 not rated for submersion but rated for water jets. The buttons were the leak path I was worried about but they seem to have good quality seals. The weak point seems to be where the wiring goes...
  5. Replies
    71
    Views
    4,450

    A few parts arrived that I will be able to use to...

    A few parts arrived that I will be able to use to make a breakout cable.
    http://greenhulk.net/forums/attachment.php?attachmentid=451138&stc=1
  6. Replies
    71
    Views
    4,450

    No problem, whats the point of a forum if we...

    No problem, whats the point of a forum if we don't have a positive and open discussion?

    I have been waiting for years to get schooled up on how to read these maps so I am stoked someone who does...
  7. Replies
    29
    Views
    1,853

    I finally got the time to tear down the engine...

    I finally got the time to tear down the engine and to my surprise the Cylinders are perfect and still have the cross hatching from the factory, but the pistons tell a different story. As I had...
  8. On the na motors, valve float shouldnt happen...

    On the na motors, valve float shouldnt happen until well over 10k since they are basically zx12r heads, with boost its a different story. Mike might know the limit since he runs a turbo setup but he...
  9. Replies
    28
    Views
    2,676

    On the rebuild really watch the oil rings on the...

    On the rebuild really watch the oil rings on the pistons, its really easy to have one pop off while installing the cylinders and get wedged between the piston and the bore. You won't notice until you...
  10. Replies
    10
    Views
    1,648

    This was info I pieced together a few years ago...

    This was info I pieced together a few years ago so take it with a grain of salt,

    00 zx12r cams are the most aggressive but have the nub in the wrong place, not really an issue if you are running a...
  11. Resolution

    For anybody looking, the 3708 ended up fitting and working. Got a NOS one off Ebay for $350. Then found out the fuel sender and speedo sensor didn't work, but all working now.
  12. Replies
    177
    Views
    88,591

    Reply sent. I will share more when I get to that...

    Its actually coming back, less custom but still modified (thank god, stock is a dirty word) but it will have different electronics and a different (stock) hull.

    Sean[/QUOTE]

    Sean, did you get...
  13. Replies
    43
    Views
    5,273

    The kawasaki manifold doesnt have a good spot for...

    The kawasaki manifold doesnt have a good spot for the o2 sensor that takes a reading from all cylinders without water in it, furthermore it is fully jacketed so you have some tough aluminum work to...
  14. Replies
    43
    Views
    5,273

    All are vr sensors the ultra uses a 24-2 wheel...

    All are vr sensors the ultra uses a 24-2 wheel and the 15f uses a 8 tooth wheel. They use unshielded non twisted wires back to the stock ecu. Both skis have a single tooth cam wheel driven off the...
  15. PART 2 - Parts Needed & Parts To Be Removed ...

    PART 2 - Parts Needed & Parts To Be Removed

    NEW PARTS LIST

    The new parts needed are shown in picture 1, the prices listed are what I PAID, you might be able to get some cheaper, some might be...
  16. Kawasaki 15F Single Muffler Free Flow Exhaust Upgrade Guide - 2009 and UP

    PART 1 - Why & What will be Upgraded?

    Kawasaki did us a big favor by removing the 2 muffler system AND the emissions systems in the 2009 and up 15F's... BUT (you knew it was coming) they crippled...
Results 1 to 16 of 18